If the Speed Queen TR7 will not spin, the guide's first checks are simple: lid closed, Start/Pause pressed, power cord in, breaker on. It also names a broken drive belt, which is a service call. If it fills and agitates but the spin is weak, or the Wash and Spin lights flash twice, the guide says the washer did not reach maximum speed in the final spin because of an unbalanced load, excess suds or slow draining; open the lid or press Start/Pause to clear the code and rebalance the load.
Differential
Likely causes of “Speed Queen TR7 top-load washer will not spin or leaves clothes soaking wet”, and how to tell them apart
- 1
An unbalanced load
What separates it The washer pauses, retries or flashes the Wash and Spin lights twice
How to confirm Redistribute the load, spreading the heavy items evenly, and then run Spin Only
- 2
Excess suds
What separates it There is foam in the tub during the spin because there are excess suds
How to confirm Use HE detergent and less of it; half the label amount if it is non-HE
- 3
Slow draining leaving too much water in the tub
What separates it The tub still holds water when the spin starts
How to confirm Check the drain hose and the receptacle, and clear anything that slows the draining
- 4
A broken drive belt
What separates it The tub neither agitates nor spins while the motor runs
How to confirm Unplug and call service; the guide lists a broken belt as a service call
Before you touch a setting
Record this first — changing settings destroys the evidence
- Whether the washer agitates and drains normally
- Which of the status lights flash on the panel
- How wet the load is at the end
Try in this order
0 of 5 completedCheck the basics
ReversibleCheck the basics, making sure that the lid is closed, the cord is in, the breaker is on and Start or Pause is pressed.
Rebalance the load
ReversibleRebalance the load, by opening the lid, spreading heavy items evenly, and rerunning Spin Only.
Reduce suds
ReversibleReduce the suds, by using less HE detergent, and running an extra rinse, and then test again to see whether it helped.
Check the drain
ReversibleMake sure the drain hose and receptacle are clear so water leaves before the spin.
Clear the code
ReversibleClear the code, by opening the lid or pressing Start or Pause, and unplugging the washer for fifteen seconds if lights persist.
Model-specific
What is true of this model and not of its siblings
- Spin and lid lock
- The TR7 will not fill, agitate or spin with the lid open, and the lid locks after the first wetdown fill and before agitation begins. A spin that never starts with the Lid Lock light flashing is a lid problem first, and a drive problem only after the lid checks pass.
- Parts for this problem on the TR7 (RepairClinic, 2026-09-20)
- motor, 3-ph induction, part number 204011P, at $500.89; belt, part number 204690, at $21.57; lid lock kit, part number 205222, at $104.56; control board, regulates the fill, wash, sin and, part number 204659P, at $405.80.
- Other models this page answers
- These steps also fit the TC5 classic-clean top-load washer, TR3 top-load washer, TR5 top-load washer.
Stop boundary
When this stops being a self-service repair
- !If the tub will not turn at all, call service for a possible drive belt
- !If the code returns after balancing and reducing suds, call service
Evidence ledger
Sources behind this answer
A dealer listing giving the TR7's capacity and cabinet size.
Parts and list prices as shown on RepairClinic's parts search for this model number on 2026-09-20.
Exact questions
Common questions
Why does the TR7 flash Wash and Spin twice?+
The guide says it did not reach maximum speed in the final spin: an unbalanced load, suds or slow draining.
How do I clear that code?+
Open the lid or press Start/Pause.
What if it will not agitate or spin?+
Check the lid and power; a broken drive belt is the guide's stated cause and needs service.
Why are my clothes too wet?+
An unbalanced load or a load that is too small; the guide suggests redistributing or adding items.
How fast does the TR7 spin?+
The guide's cycle tables list a high final spin for Normal Eco and Heavy Duty.
Will an overloaded tub prevent spinning?+
It can; use proper load sizes, evenly distributed.