GE dryer leaves clothes wrinkled or tangled: for wrinkling on a GE Profile PFD95, GE's table has three causes: overdrying (choose a shorter time, remove items while they still hold a little moisture and select Less Dry or Damp), letting items sit after the cycle (remove them when the cycle ends and fold or hang at once, or use Wrinkle Care) and overloading (separate large loads). Wrinkle Care gives 1 hour of no-heat tumbling after drying. For dry, wrinkled items the PFD95 also has steam cycles, STEAM Refresh for 3 to 5 garments and STEAM Dewrinkle for 9 to 13, both needing High temperature and the water turned on.
Differential
Likely causes of “GE dryer leaves clothes wrinkled or tangled”, and how to tell them apart
- 1
Overdrying
What separates it The cottons and synthetics come out stiff and creased because of overdrying
How to confirm Select a shorter time or Less Dry or Damp, and remove items while a little moisture remains
- 2
Items left in the dryer after the cycle ends
What separates it The wrinkles set after the drum stopped because items were left in the dryer after the cycle ended
How to confirm Remove and fold or hang at once, or turn on Wrinkle Care
- 3
Overloading
What separates it The load comes out packed and creased in the middle
How to confirm Separate large loads into smaller ones, and dry again
- 4
Too many garments for a steam cycle
What separates it The garments are still wrinkled after a steam cycle because there were too many garments for a steam cycle
How to confirm Load fewer garments, and manually increase the time
Before you touch a setting
Record this first — changing settings destroys the evidence
- The cycle, Level, Temp. and whether Wrinkle Care was on
- How many garments and how long they sat afterwards
- Whether a steam cycle was used and whether the water was turned on
Try in this order
0 of 5 completedStop overdrying
ReversibleGE says to select a shorter drying time, remove items while they still hold a slight amount of moisture and select a Less Dry or Damp setting. Damp Alert beeps when clothes have dried to a damp level.
Use Wrinkle Care
ReversibleWrinkle Care minimizes wrinkles by tumbling for 1 hour without heat after the clothes are dry. With Sound on it signals at the end of the drying time and several times to remind you to remove the clothes.
Unload promptly
ReversibleRemove items when the cycle ends and fold or hang immediately. GE says to place clothes on hangers so wrinkles will not set in, especially polyester, knits and permanent press.
Use a steam cycle for dry wrinkled items
ReversibleSTEAM Refresh is for slightly wrinkled dry garments, 3 to 5 garments; STEAM Dewrinkle is for larger loads of 9 to 13 garments and ones left in the dryer for a long time. Both need High temperature and the water on, and are not for towels.
Check the steam nozzle
ReversibleIf you cannot see steam during a cycle, the nozzle might be clogged with debris from your water supply; GE offers nozzle replacement kit WE25M71 through 877.959.8688.
Model-specific
What is true of this model and not of its siblings
- Wrinkle-related options
- The Static option sprays a mist of water at the end of the drying cycle to reduce static and is not available with Bulky, Sanitize or steam cycles. Damp Alert beeps at a damp level so you can remove items to hang. AIR FLUFF gives 10 minutes of tumbling with no heat. The Sound pad changes signal loudness, and a signal is recommended for polyester, knits and permanent press that must be removed promptly.
- Parts for this problem on the PFD95 (RepairClinic, 2026-09-21)
- main board, part number WE22X39117, at $183.62; dryer drum drive motor, part number WE03X39037, at $136.52.
- Other models this page answers
- These steps also fit models GFD85, GFD65, GTD84, GTD65, GTD58, GTD45, PTD90.
Stop boundary
When this stops being a self-service repair
- !If a steam cycle shows no steam at all, note that GE lists a clogged steam nozzle and offers replacement kit WE25M71
- !If garments come out scorched or melted, check the temperature setting and the filter before another load
Evidence ledger
Sources behind this answer
GE Appliances' own support article for a dryer that tumbles but does not heat.
GE's own page for the Profile 7.8 cu ft smart front-load electric dryer with steam, listing the manual, installation guide and warranty.
Parts and list prices as shown on RepairClinic's parts search for this model number on 2026-09-21.
Exact questions
Common questions
How do I stop wrinkles in a GE dryer?+
Remove items while a slight amount of moisture remains, unload promptly, use Wrinkle Care and do not overload.
What does Wrinkle Care do?+
It provides 1 hour of no-heat tumbling after the clothes are dry.
Which garments suit STEAM Refresh?+
Slightly wrinkled dry garments in small loads of 3 to 5 items.
Which suit STEAM Dewrinkle?+
Larger loads of 9 to 13 garments, ideal for loads left in the dryer for an extended time.
Can I steam towels?+
No. Steam cycles are not intended for use with towels.
Is steam visible?+
Steam is released at different times in the cycle, so you may not see it at the start. Water dripping from the door afterwards is normal.
Do steam cycles need water?+
Yes. The water must be turned on and the temperature set to High.
Why is the door foggy after a steam cycle?+
Steam condenses on the inner door, which is normal.