Direct answer
For the LG WashTower WKEX200H dryer section, prove power, door switch, control lock and the Start-button hold behavior before internal repair. First, test the outlet/breaker and close the door firmly.
What this covers
- LG WashTower WKEX200H dryer section (WKEX200H*)
- Stacked WashTower; this record covers the dryer section and shared controls.
- The specific fault this record addresses: will not start
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The door isn't fully latched even though it looks closed
What separates it The door swings shut but doesn't click, or a bulging load is holding it slightly open at the latch even though it appears closed from a glance.
How to confirm Open, redistribute so nothing is pinched at the seal, and close firmly until an audible latch click is heard.
- 2
Control lock or a child-lock mode is active
What separates it Buttons respond with a beep or a flashing lock icon rather than starting the cycle, and this began after someone pressed and held a button combination, intentionally or not.
How to confirm Check the manual for the exact lock icon and the specific button-hold sequence that disables it — it is not the same sequence on every brand.
- 3
A delayed start was set unintentionally
What separates it The display shows a countdown or a time rather than the expected cycle progress, and the dryer will start on its own later rather than never.
How to confirm Cancel the delayed start setting explicitly rather than waiting, if immediate drying is needed.
- 4
No household power is reaching the control board
What separates it The display is fully dark rather than showing an error, lock icon or delayed-start countdown — a true no-power condition looks and behaves differently from a control refusing to start.
How to confirm Test the outlet and breaker before assuming a control-board fault; see the no-power symptom for that path.
- 5
The door switch itself has failed
What separates it The door demonstrably latches with an audible click, no lock icon or delay is showing, and it still refuses to start — this is the conclusion only after the more common causes above are ruled out.
How to confirm With power removed, a technician can test the door switch's continuity in both open and closed positions; a switch reading open when the door is physically closed confirms the fault.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- The exact display state at the moment Start is pressed — blank, showing a lock icon, showing a countdown, or showing nothing has changed.
- Whether the door produces an audible latch click when closed.
- Whether anyone recently pressed and held any button combination, intentionally or by leaning on the panel.
Test power at the outlet and breaker
ReversibleRule out a true no-power condition before troubleshooting the door or lock state.
Close the door firmly and confirm the audible latch
ReversibleRedistribute any load pinched at the door seal first.
Check for and clear control lock or an active delayed start
ReversibleUse the manual's exact sequence for this model rather than a generic guess.
Start and stop one empty Timed Dry cycle to confirm normal operation
ReversibleConfirm the fix holds before loading laundry back in.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- WKEX200H*. Stacked WashTower; this record covers the dryer section and shared controls.
- Type — WashTower DRYER section (stacked, shared panel)
- This is the DRYER half of the LG WashTower — an electric vented dryer stacked above the washer, sharing ONE center control panel with it. A control/power fault can affect both halves, and a centrally shown code may belong to the washer or the dryer, so identify the dryer section first.
- Fuel — ELECTRIC (vented)
- ELECTRIC vented on 240V. No heat with the drum turning is often a half-tripped double breaker; reset both halves. It has an exhaust vent that must be kept clear.
- Venting & features
- Clogged lint screen or blocked duct is the top cause of long drying. Sensor Dry and ThinQ Wi-Fi; the dryer's lint filter is easy-reach on the WashTower's center panel design.
- Symptom boundary
- This record covers LG WashTower WKEX200H dryer section when it will not start. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Unplug for a hot plug, damaged cord, breaker trip or burning smell before attempting anything else.
- !A door switch that tests as failed, or a control board with no display and confirmed good power, needs a technician.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "Power Issues - Laundry Dryer". LG's dryer article for a machine that will not start or respond — outlet, breaker, door and Start-button checks. What that article does not carry is the model boundary — it is written for a product line, and WKEX200H* is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
The dryer on my LG WashTower isn't heating but the washer works.+
The WashTower's washer and dryer are independent machines sharing one panel, so the dryer can fail while the washer is fine. Treat the dryer on its own: reset the 240V double breaker (a half-trip leaves the drum turning with no heat), and clean the lint filter and exhaust vent. If a code shows on the shared display, check whether it is a dryer or washer code. The washer below is unaffected by the dryer's heat problem.
The door looks closed but the dryer won't start.+
Check for an audible latch click — a bulging load can hold the door just enough off-latch that it looks closed without actually engaging the switch. Redistribute the load and close it firmly.
The panel beeps and shows a lock symbol when I press Start.+
Control lock is active. The button-hold sequence to clear it is model-specific — check the manual rather than guessing, since holding the wrong button can set other options instead.
The display shows a countdown instead of starting.+
A delayed start was set. Cancel it explicitly through the menu rather than waiting or repeatedly pressing Start, which won't override an active delay.
Does this answer apply to every LG model?+
No. It is scoped to WKEX200H*. Stacked WashTower; this record covers the dryer section and shared controls.
What should I record before troubleshooting won't start or not running?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing won't start, not running. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Unplug for a hot plug, damaged cord, breaker trip or burning smell.
Answer for the exact device and software version shown above.