For wrinkling on a Maytag MED8630, Maytag's help gives two causes and the fix for each: the load was not removed at the end of the cycle, so select Wrinkle Prevent to tumble it without heat, and the dryer was tightly packed, so dry smaller loads that can tumble freely. On this model Wrinkle Prevent adds up to 150 minutes of periodic tumbling, and on steam models the +Steam setting adds a short steam phase after 60 minutes. Steam adds about 15 minutes to selected sensor cycles and is not available on Sanitize, Delicates, Steam Refresh or timed cycles.
Differential
Likely causes of “Maytag dryer leaves clothes wrinkled or tangled”, and how to tell them apart
- 1
The load sat in the dryer after the cycle
What separates it The creases set after the cycle ended because the load sat in the dryer after the cycle
How to confirm Take the load out at End, or select Wrinkle Prevent before starting
- 2
A tightly packed drum
What separates it The clothes come out with deep folds because of a tightly packed drum
How to confirm Dry smaller loads that can tumble freely, and dry again
- 3
A temperature or dryness too high for the fabric
What separates it The synthetics feel stiff and creased because the temperature or dryness is too high for the fabric
How to confirm Choose a lower Temp. and a sensor cycle to avoid overdrying
- 4
A dry load that needs steam rather than heat
What separates it The cotton blends and knits are dry but creased because a dry load needs steam rather than heat
How to confirm Use the Steam option or the Steam Refresh cycle on steam models
Before you touch a setting
Record this first — changing settings destroys the evidence
- Which cycle, temperature and dryness you used
- Whether Wrinkle Prevent or Steam was selected
- How long the load sat before it was unloaded
Try in this order
0 of 5 completedLoad fewer items
ReversibleLoad fewer items, since Maytag says a tightly packed dryer causes wrinkles, so dry smaller loads that tumble freely.
Use Wrinkle Prevent
ReversibleTouch Wrinkle Prevent before starting to add up to 150 minutes of periodic tumbling if you cannot remove the load right away.
Unload promptly
ReversibleSelect the option or take the load out as soon as the cycle ends; wrinkles form when laundry sits after the tumbling stops.
Lower the temperature
ReversibleUse the lower setting rather than the higher one if unsure, and a sensor cycle, which senses moisture and stops at the selected dryness to reduce overdrying.
Try the steam option
ReversibleOn steam models the +Steam setting on some cycles adds a short steam phase after 60 minutes, and Steam adds about 15 minutes to a sensor cycle to help smooth wrinkles.
Model-specific
What is true of this model and not of its siblings
- Steam and Static Reduce on steam models
- Steam adds steam to the end of certain sensor cycles to smooth wrinkles and adds about 15 minutes; Static Reduce is added to selected sensor cycles, tumbles, pauses and introduces a small amount of moisture, and adds about 3 minutes. Steam models need water connected through inlet hoses that must not be kinked; the manual says to replace hoses after 5 years.
- Parts for this problem on the MED8630 (RepairClinic, 2026-09-21)
- steam dryer heavy duty fill hose kit that includ, part number W10623830, at $48.45; $60.00 cash back prog acu - janus ul4, 8630, ele, part number W11388027, at $393.35; dryer drum drive belt, 93 1/2 inches long, 4 rib, part number 661570V, at $28.38.
- Other models this page answers
- These steps also fit models MED6630, MED5630, MED7230, MED6200, MED4500, MGD8630.
Stop boundary
When this stops being a self-service repair
- !If items come out scorched or melted rather than wrinkled, check the temperature setting and vent before another cycle
- !If steam leaves water on the door on a normal load, contact Maytag service
Evidence ledger
Sources behind this answer
Maytag's own quick start guide for this model: the touch panel, Cycle Control knob with Extra Power, Check Vent indicator, Control Lock, Wrinkle Prevent, Steam and Static Reduce options.
Maytag's own help articles for its dryers, each: not heating, long dry times, not starting, not tumbling, stops mid-cycle, wrinkled clothing, sounds, odor and no power.
Maytag's own listing for this model's manuals and support.
Parts and list prices as shown on RepairClinic's parts search for this model number on 2026-09-21.
Exact questions
Common questions
Why are my clothes wrinkled?+
Usually because the load sat after the cycle or was packed too tightly.
How long does Wrinkle Prevent run?+
Up to 150 minutes of periodic tumbling.
Does Steam add time?+
Yes, about 15 minutes to the cycle.
Where is Steam not available?+
Sanitize, Delicates, Steam Refresh and timed cycles such as Timed Dry and Quick Dry.
What does Static Reduce add?+
About 3 minutes; the dryer tumbles, pauses and adds a small amount of moisture.
Can I use High heat with steam?+
Steam can be used with High or Medium heat settings.
What if my dryer is not a steam model?+
Use Wrinkle Prevent, smaller loads and prompt unloading.
Is prompt unloading enough?+
It is the most effective fix; Wrinkle Prevent covers the delay.