Direct answer
For the Dyson V8 cordless vacuum, hair wrap, floor setting, blockage, belt/head power and overload protection should be separated. First, disconnect power and clear the roll/end caps.
What this covers
- Dyson V8 cordless vacuum (SV10/SV25 / V8)
- Dyson vacuum; filter, battery, cleaner head and LCD fault behavior vary by model.
- The specific fault this record addresses: brush roll will not spin
What it does not cover
- ×The same symptom on a different Dyson product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
Hair or thread is wrapped around the roll's end bearings
What separates it The roll spins with visible resistance or not at all, and pulling gently on visible strands at either end reveals more wound underneath.
How to confirm With power disconnected, remove the roll per the model's tool-free or tool-assisted release and clear wrapped material fully, including under the end caps.
- 2
The floor-type setting doesn't match the surface, or auto-adjust height sensing has a fault
What separates it The brush works on one floor type (hard floor or carpet) but not the other, or the head visibly doesn't adjust height when moved between surfaces.
How to confirm Manually cycle through the floor-type settings if the model has them, and confirm the auto-height mechanism moves freely on both surfaces.
- 3
The drive belt has broken (belt-driven models only)
What separates it The roll spins completely freely by hand with no resistance and the motor runs, but the roll doesn't turn under power at all.
How to confirm This applies only to belt-driven brush systems; direct-drive brush motors don't have this failure mode.
- 4
Overload protection has tripped from a jam
What separates it The brush stopped abruptly during use, possibly with a brief burning-rubber smell, rather than never having worked.
How to confirm Clear the jam fully, let the unit cool per the manual, and it should reset on the next power cycle.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether the roll spins freely by hand with power disconnected, resists, or is fully seized.
- Whether the problem is on one floor-type setting only or across all settings.
- Any visible hair, thread or debris wrapped around the roll or its end caps.
Disconnect power before any inspection
ReversibleNever inspect or clear a brush roll while the vacuum is powered.
Remove the roll and clear wrapped hair or thread from the entire length and end caps
ReversibleThis resolves the large majority of brush roll complaints.
Confirm free rotation by hand after clearing
ReversibleTest on the correct floor-height setting for the surface being used.
Arrange service or replacement for a confirmed broken belt or failed brush motor
ReversibleThis is a customer-replaceable part on most models once diagnosed.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- SV10/SV25 / V8. Dyson vacuum; filter, battery, cleaner head and LCD fault behavior vary by model.
- Type — cordless stick (battery)
- An older CORDLESS STICK with two power modes and a (non-click-in on early units) battery. Max power drains faster; pulsing/stopping is usually a blocked airway or a hot/cold battery.
- Filter & airway
- Washable filter(s) — wash monthly, dry fully before refitting. Clear the wand, bin inlet and cyclone for suction loss.
- Age
- As an older model, a big drop in runtime is often normal battery ageing; replacement batteries are available. Confirm full charging first.
- Symptom boundary
- This record covers Dyson V8 cordless vacuum when it brush roll will not spin. A different symptom on the same hardware, or this symptom on a different Dyson product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Stop for hot rubber smell, melted plastic, sparks, or a roll that's seized solid even after clearing debris.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. Dyson Support publishes this as "Product support". Official Dyson troubleshooting, maintenance, parts and repair entry point. What that article does not carry is the model boundary — it is written for a product line, and SV10/SV25 / V8 is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
My older Dyson V8 only runs for a few minutes now.+
Battery ageing is the usual cause on an older cordless — lithium cells lose capacity over years of charging, so runtime shortens. A replacement battery restores it (much cheaper than a new vacuum). First rule out the simpler causes: wash and fully dry the filter, clear any blockage in the wand and bin, and confirm it charges fully. High power mode also always runs shorter than the standard mode.
The brush roll won't spin and I can see hair wrapped around it.+
This is by far the most common cause. With power fully disconnected, remove the roll per the model's release mechanism and clear the wrapped hair from the entire roll and both end caps — hair often hides under the caps even when the visible middle looks clear.
Does this answer apply to every Dyson model?+
No. It is scoped to SV10/SV25 / V8. Dyson vacuum; filter, battery, cleaner head and LCD fault behavior vary by model.
What should I record before troubleshooting brush not spinning or roller?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing brush not spinning, roller. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop for hot rubber, melted parts, sparks or a seized roll.
Answer for the exact device and software version shown above.