Direct answer
For the LG WashTower WKEX300H washer section, excess or non-HE detergent can extend the cycle, suppress spin and cause drain errors. First, pause additions and let the washer complete its suds-removal routine.
What this covers
- LG WashTower WKEX300H washer section (WKEX300H*)
- WashTower model with center controls; confirm washer versus dryer status.
- The specific fault this record addresses: shows excessive suds, SUD or Sd behavior
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
Non-HE detergent was used
What separates it Heavy visible foam, an extended cycle, and possibly a suds error code. Standard detergent is formulated to foam in a full tub of water and overwhelms a high-efficiency machine.
How to confirm Check the detergent for the HE symbol. This is the most common cause by a wide margin.
- 2
Too much HE detergent was used
What separates it The right product but a heavy hand, or a dose scaled to a large load that was not actually large.
How to confirm Compare the dose against the manual's stated amount for the load size and local water hardness — soft water needs noticeably less.
- 3
The load was lightly soiled but dosed as heavily soiled
What separates it Suds problems on ordinary loads that get a full-cap dose out of habit.
How to confirm Reduce to the light-soil dose and retest with the same load type.
- 4
Detergent residue has built up in the machine over time
What separates it Suds appear even after switching to a correct dose, persisting over several loads.
How to confirm Run the manufacturer's tub-clean cycle with no laundry and no detergent, repeating if foam still appears.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether the detergent carries the HE symbol.
- The actual dose used, measured against the manual's stated amount for that load size.
- The local water hardness, since soft water requires substantially less detergent.
- Whether foam persists across several loads after correcting the dose, which points at accumulated residue.
Let the machine complete its own suds-removal routine
ReversibleExtra rinses and pauses are the machine clearing foam, not a malfunction — interrupting it leaves detergent in the load.
Confirm the detergent is HE and reduce to the manual's stated dose
ReversibleScale to load size and water hardness; soft water needs noticeably less than the package suggests.
Run the manufacturer's tub-clean cycle with no laundry and no detergent
ReversibleClears accumulated residue that keeps producing foam after the dose is corrected.
Confirm the next normal load completes without foam or repeated drain pauses
ReversibleOne clean cycle confirms the correction.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- WKEX300H*. WashTower model with center controls; confirm washer versus dryer status.
- Type — WashTower: stacked washer + dryer, one control panel
- A larger-capacity WashTower with the washer below, dryer above, and ONE shared center control panel. As with any WashTower, a control/power fault can affect both halves together, and a centrally shown code may belong to either section — determine washer-versus-dryer first.
- Motor — Direct Drive inverter (no belt)
- Belt-less Direct Drive inverter washer motor; noise/vibration is bearings and balance, not a belt.
- Smart
- ThinQ Wi-Fi with AI-sensing. Washer front-load gasket care for odour; the dryer needs normal lint/vent maintenance.
- Symptom boundary
- This record covers LG WashTower WKEX300H washer section when it shows excessive suds, SUD or Sd behavior. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Do not add any chemical intended to break down suds unless the manufacturer explicitly permits it — some damage seals and finishes.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "Too Many Suds in Washing Machine". Excessive suds and the SUD/Sd hold behaviour, with LG's HE-detergent dosing guidance. What that article does not carry is the model boundary — it is written for a product line, and WKEX300H* is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
How do I tell if it's the washer or dryer at fault on my LG WashTower?+
Because the WashTower shares one control panel, note which drum the problem is in and which controls respond. Run each half on its own: start a short wash and, separately, a short dry, and watch which one shows the error or fails to start. A code on the shared display often has a washer or dryer prefix in the manual. Isolating the section first stops you troubleshooting the wrong machine.
What does the SUD or Sd code mean?+
The machine has detected more foam than it can drain or spin through, so it is adding rinses and pausing to clear it. That is suds management working rather than a fault. The usual cause is non-HE detergent, or too much HE detergent for the load size and water hardness.
I switched to less detergent but I'm still getting suds.+
Residue accumulated in the machine keeps producing foam for a while after the dose is corrected. Run the manufacturer's tub-clean cycle with no laundry and no detergent, and repeat it if foam still appears on the next load.
Does this answer apply to every LG model?+
No. It is scoped to WKEX300H*. WashTower model with center controls; confirm washer versus dryer status.
What should I record before troubleshooting SUD or Sd or too many suds?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing SUD, Sd, too many suds. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Do not add chemicals intended to neutralize suds unless the manufacturer explicitly permits them.
Answer for the exact device and software version shown above.