Direct answer
For the LG WT6105CW top-load washer, load balance, shipping hardware, cabinet level and floor stiffness should be proved before suspension or drive repair. First, stop the cycle and compare empty spin with a balanced towel load.
What this covers
- LG WT6105CW top-load washer (WT6105CW)
- LG top-load washer; ThinQ-enabled controls and menu paths vary by model.
- The specific fault this record addresses: shakes, walks or bangs during spin
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The load is unbalanced
What separates it Movement happens only on certain loads — a single comforter, a bath mat, a few heavy towels — and not on normal mixed loads.
How to confirm Redistribute into an even ring around the drum and re-run the spin. Bulky single items are the most common cause and are not a fault.
- 2
The machine is not level or a foot is not carrying weight
What separates it The cabinet rocks when pushed diagonally at a top corner, and vibration happens across many different loads rather than specific ones.
How to confirm Adjust the leveling feet until all four carry weight and the cabinet does not rock, then re-tighten any locking nuts against the cabinet.
- 3
The floor is flexing under the machine
What separates it The machine is confirmed level and does not rock, but the whole floor perceptibly moves during spin — common on suspended wooden floors, especially upstairs.
How to confirm This is a structural condition rather than an appliance fault; a solid platform or plywood underlayment is the remedy, not a machine repair.
- 4
Suspension rods, springs or dampers have worn out
What separates it A machine that used to spin quietly now moves excessively on ordinary balanced loads, with level and load ruled out. On a top-load machine this often shows as the tub visibly striking the cabinet.
How to confirm This is a service diagnosis reached once shipping bolts, load, level and floor are all eliminated.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether the machine has ever spun quietly, or has banged since installation — the latter points immediately at shipping bolts on a front-load machine.
- Whether movement happens on all loads or only bulky single items.
- Whether the cabinet rocks when pushed diagonally at a top corner.
- Whether the floor itself moves during spin.
Stop the cycle and compare an empty spin against a balanced towel load
ReversibleAn empty spin that is quiet and a loaded spin that is violent points at load distribution rather than hardware.
Level the cabinet so all four feet carry weight and it does not rock
ReversibleRe-tighten the locking nuts against the cabinet after adjusting.
Arrange service for excessive movement on a balanced load with level confirmed
ReversibleWorn suspension rods, springs or dampers are a service repair.
Run one balanced high-speed spin and confirm the cabinet stays still
ReversibleConfirms the correction before returning to normal use.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- WT6105CW. LG top-load washer; ThinQ-enabled controls and menu paths vary by model.
- Type & capacity — entry TOP-LOAD
- 4.1 cu. ft. entry TOP-LOAD washer — the value LG top-loader. Identify AGITATOR versus IMPELLER on your unit for correct loading. HE low-water fill is normal.
- Motor — Direct Drive inverter (no belt)
- Belt-less Direct Drive inverter motor; noise/vibration is bearings and balance, not a belt.
- Feature tier
- An entry model, typically without Wi-Fi, so there is no ThinQ connectivity troubleshooting; a simple control panel means a long or paused cycle is load balance or water fill, not a smart feature.
- Symptom boundary
- This record covers LG WT6105CW top-load washer when it shakes, walks or bangs during spin. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Stop immediately for violent movement or a machine walking across the floor — it can damage itself, the floor, and nearby plumbing connections.
- !Exposed shipping hardware or repeated metal-on-metal collision means stop and correct before running another cycle.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "LG Washing Machine - Troubleshooting Washer Vibration Issues". Excessive vibration, walking and banging during spin, with LG's levelling and load-balance checks. What that article does not carry is the model boundary — it is written for a product line, and WT6105CW is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
Does the LG WT6105 connect to the ThinQ app?+
The WT6105 is LG's entry top-loader and most builds have no Wi-Fi, so they do not connect to ThinQ — app pairing and remote-start troubleshooting do not apply. Confirm your exact model's spec if unsure. Mechanically it is the same Direct Drive top-load design, so loading, balance and low-water-fill behaviour are the same as the higher WT models.
My new front-load washer bangs violently on spin.+
Check the rear panel for shipping bolts. They lock the drum suspension for transit and must be removed at installation — with them still in place the drum's movement goes straight into the cabinet, and continuing to run it that way causes permanent suspension damage.
It only shakes when I wash a comforter.+
That is an unbalanced load rather than a fault. A single bulky item cannot distribute itself around the drum, so the machine spins with all the weight on one side. Redistribute it into an even ring, or wash bulky items with a couple of towels to help balance them.
Does this answer apply to every LG model?+
No. It is scoped to WT6105CW. LG top-load washer; ThinQ-enabled controls and menu paths vary by model.
What should I record before troubleshooting shaking or vibration or walking?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing shaking, vibration, walking. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop immediately for violent movement, exposed shipping hardware or repeated metal collision.
Answer for the exact device and software version shown above.