Direct answer
For the LG WT7900HBA top-load washer, the location and cycle stage of the first drop matters more than the final puddle. First, dry the floor and observe the first leak during fill, tumble/agitation and drain.
What this covers
- LG WT7900HBA top-load washer (WT7900HBA)
- LG top-load washer; ThinQ-enabled controls and menu paths vary by model.
- The specific fault this record addresses: is leaking water
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
A supply hose connection is weeping
What separates it Water appears at the rear of the machine, is present even when the machine is idle, and is clean rather than soapy.
How to confirm Clean supply water at the back with the machine off points to a faucet or hose connection rather than anything inside the machine.
- 2
The drain hose connection has come loose or the standpipe is overflowing
What separates it Water appears at the rear or under the machine during the drain phase specifically, and is soapy rather than clean.
How to confirm Watch the standpipe during the drain phase — an overflowing standpipe is a household plumbing restriction, not an appliance leak.
- 3
Overfilling from excess suds is forcing water past a seal
What separates it Leaking correlates with loads that used heavy detergent, and foam is visible in the tub.
How to confirm See suds-foam. A machine leaking only on heavily detergent-loaded cycles is usually not mechanically faulty.
- 4
An internal tub seal or bearing has failed
What separates it Water appears from under the center of the machine during the spin phase, often alongside a growing rumbling or grinding noise.
How to confirm This is a major service repair, and the noise usually precedes the leak by weeks — see noise-grinding.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- The exact phase the first drop appears in — fill, wash, spin or drain. Each points at a different part of the machine.
- Whether the water is clean or soapy. Clean water is supply-side; soapy water is from inside the tub.
- Whether it appears at the front, rear, or from under the center of the cabinet.
- Whether the drain pump filter was cleaned recently, on a front-load machine.
Dry the floor completely and watch a short cycle to find where the first drop appears
ReversibleDiagnosing from the final puddle is unreliable because water tracks along the base before emerging.
Tighten or replace only the proven external hose connection
ReversibleInternal tub and bearing seals are a service repair, not an owner one.
Repeat the same short cycle while watching the original leak point
ReversibleConfirms the repair rather than assuming it.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- WT7900HBA. LG top-load washer; ThinQ-enabled controls and menu paths vary by model.
- Type & capacity — TOP-LOAD, mega
- 5.5 cu. ft. mega-capacity TOP-LOAD washer. Confirm whether yours has a center AGITATOR or a low-profile IMPELLER, as it changes loading and tangling advice. On a drum this large, overloading causes unbalance and a spin that won't complete.
- Motor — Direct Drive inverter (no belt)
- Belt-less Direct Drive inverter motor; noise/vibration is bearings and balance, not a belt.
- Top-load behaviour
- HE low-water fill is normal (not a fill fault). ThinQ Wi-Fi and TurboWash 3D on this tier. The lid must lock before spin — an unbalanced load or a lid-lock fault is the usual 'won't spin' cause.
- Symptom boundary
- This record covers LG WT7900HBA top-load washer when it is leaking water. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Unplug the machine and close both faucets for water spraying under pressure, a split hose, or any water reaching an outlet, wiring or the machine's own electrical components.
- !Water appearing from under the center of the cabinet during spin, with a rumbling noise, indicates a failed tub bearing — stop using the machine, because continuing will damage it further.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "Leaking - Washing Machine Troubleshooting Guide". LG's leak-source guide — hose connections, door gasket, dispenser, drain — for water appearing under or around the machine. What that article does not carry is the model boundary — it is written for a product line, and WT7900HBA is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
My big LG WT7900 won't spin or leaves clothes soaked.+
On a large top-loader this is usually load balance. A heavy single item (comforter, towels bunched to one side) prevents the drum from balancing, so the machine reduces or skips the fast spin to avoid banging. Redistribute the load evenly around the drum and restart the spin. Also confirm the lid locks — the spin will not start if the lid switch is not engaging.
It started leaking right after I cleaned the drain filter.+
Check the filter cap seal — an incompletely threaded or badly seated cap is by far the most common cause of a leak that appears immediately after that maintenance. Make sure the seal is clean and the cap is fully tightened.
Water only appears at the front during the wash cycle.+
That points at the door boot seal. Pull back the rubber boot's lower fold and inspect the full circumference for trapped grit or a coin holding it open, or for a visible tear. Debris can be cleared; a tear means the boot needs replacing.
How do I tell a machine leak from a plumbing problem?+
Watch the standpipe during the drain phase. If water backs up and overflows out of the standpipe, that is a restricted household drain rather than an appliance leak — the washer is pumping correctly and the drain cannot take it.
Does this answer apply to every LG model?+
No. It is scoped to WT7900HBA. LG top-load washer; ThinQ-enabled controls and menu paths vary by model.
What should I record before troubleshooting leaking or water underneath or door leak?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing leaking, water underneath, door leak. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Unplug and close water for spraying, electrical wetting, a split hose or uncontrolled flow.
Answer for the exact device and software version shown above.