Direct answer
For the TP-Link Archer AX73 router, building loss, access-point placement, band and mesh backhaul should be measured at the node location. First, test signal/speed halfway to the weak room.
What this covers
- TP-Link Archer AX73 router (Archer AX73)
- TP-Link router/Deco; EasyMesh/Deco controller, Wi-Fi generation, HomeShield and Ethernet ports vary.
- The specific fault this record addresses: has weak signal or dead zones
What it does not cover
- ×The same symptom on a different TP-Link product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The router or node is poorly placed for that area
What separates it The weak spot is far from the router, or the router sits low, in a cabinet, or against an outside wall.
How to confirm Move the router or node higher, more central and in the open, then re-measure signal and speed halfway to the weak room — placement is the highest-leverage change.
- 2
Building materials are absorbing the signal
What separates it The dead zone is behind brick, concrete, foil-backed insulation, a metal appliance, or a large mirror or aquarium.
How to confirm Test signal on both sides of the suspected barrier; a sharp drop across one wall identifies an absorber that a repositioned or added node has to work around.
- 3
The band cannot reach that far
What separates it The device holds a fast connection near the router but a much weaker one at range, worse on 5/6 GHz.
How to confirm Compare 2.4 GHz against 5/6 GHz at the weak spot; 2.4 GHz reaches farther through walls even though it is slower, so distant rooms may need it.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- The signal and speed measured halfway to the weak room, not just in it.
- What is physically between the router/node and the dead zone.
- For a mesh: the backhaul strength reported by the node covering that area.
Measure signal and speed halfway to the weak room
ReversibleLocates where the signal actually falls off, rather than only confirming it is weak at the end.
Reposition one node or access point higher, central and in the open
ReversibleAnd compare 2.4 versus 5/6 GHz at the spot, since lower bands reach farther.
Add supported wired-backhaul or well-placed mesh coverage
ReversibleA wired backhaul to a distant node beats a weak wireless one every time.
Walk-test the original dead zone to confirm
ReversibleVerifies real coverage where the problem was, not just near the router.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- Archer AX73. TP-Link router/Deco; EasyMesh/Deco controller, Wi-Fi generation, HomeShield and Ethernet ports vary.
- Wi-Fi 6 router (single unit, dual-band)
- A Wi-Fi 6 (AX) router with 2.4/5 GHz (no 6 GHz — that is 6E/7). Wi-Fi 6 speeds need Wi-Fi 6 clients; older devices connect at their generation.
- Single router coverage
- Limited area as a single unit; add OneMesh/Deco or place centrally for large homes. A weak room is coverage, not a fault.
- Managed by Tether app or web
- TP-Link Tether app or web admin. No 6 GHz band (generation limit).
- Symptom boundary
- This record covers TP-Link Archer AX73 router when it has weak signal or dead zones. A different symptom on the same hardware, or this symptom on a different TP-Link product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Do not run cabling through unsafe routes or place equipment where heat or moisture collects when extending coverage.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. TP-Link publishes this as "How to Improve Your Wi-Fi Signal and Range". TP-Link's coverage and signal-strength article. Probed 2026-08-21: title-verified. What that article does not carry is the model boundary — it is written for a product line, and Archer AX73 is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
Does my TP-Link Archer AX73 support 6 GHz Wi-Fi?+
No — the AX73 is a Wi-Fi 6 (AX) router with 2.4 and 5 GHz bands only. The 6 GHz band arrived with Wi-Fi 6E (the AXE models) and Wi-Fi 7. So there is no 6 GHz network to find on it, which is its generation rather than a fault. It still gives strong Wi-Fi 6 performance to compatible devices on 5 GHz.
One room always has terrible Wi-Fi.+
That is a coverage gap, and placement is the biggest lever. Try the router or a node higher, more central and out of any cabinet first, and measure signal halfway to that room to find where it drops off. If a wall of brick, concrete or foil-backed insulation is in the way, you will likely need a node on the far side — ideally with a wired backhaul — and on distant rooms the slower 2.4 GHz band often reaches where 5 GHz cannot.
Does this answer apply to every TP-Link model?+
No. It is scoped to Archer AX73. TP-Link router/Deco; EasyMesh/Deco controller, Wi-Fi generation, HomeShield and Ethernet ports vary.
What should I record before troubleshooting dead zones or weak signal?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing dead zones, weak signal. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Do not route unsafe cables or place equipment in heat/moisture.
Answer for the exact device and software version shown above.