Direct answer
For the TCL 4-Series Roku TV S455, correct labeled ports, matching CEC/eARC controls, output format and direct-chain testing matter. First, use the labeled ARC/eARC ports and test PCM/stereo.
What this covers
- TCL 4-Series Roku TV S455 (43/50/55/58/65/75/85S455)
- TCL TV; Roku TV, Google TV and Fire TV platforms use different menus and app stores.
- The specific fault this record addresses: ARC or eARC soundbar audio is not working
What it does not cover
- ×The same symptom on a different TCL product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The cable is in the wrong HDMI port
What separates it No audio to the soundbar, with the cable in any port other than the one labelled ARC or eARC.
How to confirm Only one port on the television supports ARC/eARC and it is labelled. This is the most common cause by a wide margin and takes seconds to check.
- 2
HDMI-CEC is disabled on one of the devices
What separates it The soundbar does not power on with the TV, volume control does not pass through, and audio does not route.
How to confirm ARC depends on CEC, and every manufacturer gives it a different name — Anynet+, Bravia Sync, Simplink, VIERA Link. It has to be enabled on both devices.
- 3
The TV's audio output is not set to the ARC device
What separates it Sound continues from the TV speakers with the soundbar connected and powered.
How to confirm Set the audio output explicitly to the HDMI/ARC device rather than relying on automatic detection.
- 4
The cable cannot carry eARC bandwidth
What separates it ARC works but eARC does not, or high-bitrate formats such as Dolby TrueHD or DTS:X fail while compressed formats play.
How to confirm eARC needs substantially more bandwidth than ARC. A cable adequate for ARC can fail at eARC, and manufacturers generally specify a High Speed with Ethernet or Ultra High Speed cable.
- 5
The audio format exceeds what the soundbar supports
What separates it Silence on specific content only, typically Dolby Atmos or DTS:X.
How to confirm Set the TV's output to PCM as a test. If sound returns, the soundbar cannot decode what was being sent.
- 6
The CEC link has stalled
What separates it It worked before and stopped with nothing changed.
How to confirm Power everything off, unplug both devices for 60 seconds, then power the TV on first and the soundbar second. CEC links stall regularly and this clears most.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Which HDMI port the cable is in, and whether that port is the one labelled ARC or eARC.
- Whether HDMI-CEC is enabled on both devices, under whatever name each manufacturer uses.
- Whether the failure is total, or only on specific high-bitrate formats.
- The cable's rating, since eARC requires more bandwidth than ARC.
Confirm the cable is in the port labelled ARC or eARC
ReversibleOnly one port on the television supports it, and this is the single most common cause.
Enable HDMI-CEC on both devices
ReversibleEach manufacturer names it differently — Anynet+, Bravia Sync, Simplink, VIERA Link — and it must be on at both ends.
Set the TV's audio output explicitly to the HDMI/ARC device
ReversibleAutomatic detection frequently fails to switch over.
Set the output format to PCM as a test
ReversibleIf sound returns, the soundbar cannot decode the surround format that was being sent.
Power-cycle both devices with a 60-second unplug, TV powered on first
ReversibleA stalled CEC link is common and this clears most of them.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- 43/50/55/58/65/75/85S455. TCL TV; Roku TV, Google TV and Fire TV platforms use different menus and app stores.
- Panel — entry direct-lit LED (no QLED)
- The 4-Series S455 is TCL's entry tier: a direct-lit LED LCD with no quantum-dot QLED layer and no local dimming. Blacks are grey in a dark room and backlight uniformity is more visible; that is the limit of the tier, not a defect.
- Smart platform — ROKU TV
- Runs Roku OS built in. Update at Settings › System › System update; Miracast/AirPlay 2 mirroring; Roku remote and app store. Not Google TV.
- Picture / gaming limits
- 4K resolution with HDR10 and HLG (limited HDR impact because the panel is not bright), a native 60 Hz panel and HDMI 2.0 — no 4K 120 Hz or VRR. A request for high-refresh or strong HDR is beyond this model's hardware.
- Symptom boundary
- This record covers TCL 4-Series Roku TV S455 when it ARC or eARC soundbar audio is not working. A different symptom on the same hardware, or this symptom on a different TCL product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Do not use HDMI splitters or switches in an ARC path unless they explicitly support ARC/eARC — most break it entirely.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. TCL Support publishes this as "TV support". Official TCL manuals, firmware, Roku TV and Google TV troubleshooting support. What that article does not carry is the model boundary — it is written for a product line, and 43/50/55/58/65/75/85S455 is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
Why does HDR look dull on my TCL 4-Series?+
The 4-Series S455 is an entry direct-lit LED TV without QLED colour or local dimming, and it is not bright enough to show much HDR impact — so HDR content can look flat or dull. That is the hardware tier, not a fault or a wrong setting. Brighter HDR needs a QLED (5-Series and up) or a Mini-LED TCL.
My soundbar gets no audio over ARC.+
Check which HDMI port the cable is in first. Only one port on the television supports ARC or eARC, and it is labelled — a cable in any other port gives exactly this symptom, and it is the most common cause by a wide margin. After that, make sure HDMI-CEC is enabled on both devices; every brand calls it something different.
ARC works but eARC doesn't.+
That is almost always the cable. eARC carries far more bandwidth than ARC to support uncompressed and object-based formats, so a cable that is perfectly adequate for ARC can fail at eARC. Manufacturers typically specify a High Speed with Ethernet or Ultra High Speed cable for it.
Does this answer apply to every TCL model?+
No. It is scoped to 43/50/55/58/65/75/85S455. TCL TV; Roku TV, Google TV and Fire TV platforms use different menus and app stores.
What should I record before troubleshooting eARC or ARC or soundbar?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing eARC, ARC, soundbar. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop for hot ports, electrical noise, sparks or receiver protection.
Answer for the exact device and software version shown above.