Direct answer
For the GE GDT670 dishwasher, fill, circulation, spray-arm movement, loading, detergent and water temperature must all be present. First, mark spray-arm position and run a short empty wash.
What this covers
- GE GDT670 dishwasher (GDT670S*)
- GE/GE Profile dishwasher; Dry Boost, bottle jets, UltraFresh and Wi-Fi equipment varies.
- The specific fault this record addresses: does not clean dishes
What it does not cover
- ×The same symptom on a different GE product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The spray arms cannot rotate freely
What separates it Cleaning is poor in a consistent area — usually one side, or the top rack — while the rest of the load is fine. A tall item, a pan handle through the rack, or a knife blade hanging down blocks the arm's swing.
How to confirm With the machine off, spin each spray arm by hand through a full rotation. Any contact means the load blocks it, and that pattern of dirty items matches where the arm could not reach.
- 2
Spray arm jets are blocked with debris or mineral scale
What separates it Poor cleaning that is general rather than one-sided, with visible blockage in some of the small holes when the arm is inspected.
How to confirm Most spray arms unclip for cleaning. Clear the holes with a toothpick or fine wire rather than anything that could enlarge them.
- 3
The first fill is cold
What separates it Greasy soils and dried-on food persist while light soil washes fine.
How to confirm Run the kitchen hot tap until hot before starting, so the machine draws hot water immediately rather than filling with the cold water standing in the pipe.
- 4
The filter is dirty and soil is being recirculated
What separates it A gritty film redeposited on the load, sometimes worse than before washing.
How to confirm Clean the tub filter — a clogged filter means the pump recirculates the food it has already removed.
- 5
Detergent was placed in the wrong compartment or blocked from opening
What separates it The main detergent cup is still full at the end of the cycle, or a tall item was leaning against the closed door.
How to confirm See detergent-door — detergent released into the pre-wash instead of the main wash is largely rinsed away before it can work.
- 6
Items were pre-rinsed so thoroughly the sensor shortened the cycle
What separates it Poor results specifically on Auto or sensor-driven cycles after heavy pre-rinsing.
How to confirm A soil sensor reads clean water as a light load and selects a short, cool cycle. Scraping rather than rinsing gives the sensor an accurate picture, and modern detergents need some soil to work against.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether the poorly cleaned items are in one consistent area of the racks, which points at spray-arm obstruction, or scattered throughout, which does not.
- Whether the residue is dried-on original food, or a gritty redeposited film — the second points at the filter.
- Whether the detergent cup was empty at the end of the cycle.
- Whether items are pre-rinsed before loading, and which cycle is normally selected.
Spin each spray arm by hand through a full rotation with the machine off
ReversibleAny contact with the load identifies the blockage, and the dirty items will match where the arm could not reach.
Unclip the spray arms and clear blocked jets
ReversibleUse a toothpick or fine wire; do not enlarge the holes.
Clean the tub filter
ReversibleA clogged filter recirculates soil back onto the load, which shows up as a gritty film.
Run the kitchen hot tap until hot before starting the cycle
ReversibleGreasy soils need the first fill to arrive hot rather than the machine heating a tub of cold.
Scrape rather than rinse, and confirm the detergent cup empties
ReversibleOver-rinsing makes a soil sensor select a shorter, cooler cycle than the load actually needs.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- GDT670S*. GE/GE Profile dishwasher; Dry Boost, bottle jets, UltraFresh and Wi-Fi equipment varies.
- Drying — Dry Boost
- Dry Boost fan-plus-heat active drying, good on plastics when enabled. Rinse aid helps.
- Wash & racks
- Stainless tub and a 3rd rack; bottle jets on some builds. A manual filter must be cleaned periodically.
- Drain path
- 'Won't drain' is usually the filter, drain hose, air gap, or an un-removed disposer knockout plug.
- Symptom boundary
- This record covers GE GDT670 dishwasher when it does not clean dishes. A different symptom on the same hardware, or this symptom on a different GE product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Stop for grinding noises, broken glass in the sump, leaks, or a burning odour.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. GE Appliances publishes this as "Dishwasher - Poor Wash Performance". GE Appliances' own troubleshooting article for this symptom. Title and text were read from GE's article at harvest (docs/verification/ge-articles.json) and the URL re-checked 2026-09-01. What that article does not carry is the model boundary — it is written for a product line, and GDT670S* is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
My GE GDT670 has a film on glasses.+
Film is usually hard water and rinse aid. Fill and raise the rinse-aid dosage, and in hard-water areas run a dishwasher cleaner/descaler periodically and consider a detergent with a built-in softener. A cloudy etch that will not wipe off can be permanent glass etching from too much detergent plus soft water — reduce detergent. Make sure the water is hot and the filter is clean, too.
Only the dishes on one side come out dirty.+
That pattern almost always means a spray arm cannot complete its rotation. With the machine off, spin each arm by hand through a full circle — a tall item, a pan handle poking through the rack, or a knife hanging down is usually catching it, and the dirty area matches exactly where the arm could not reach.
Should I rinse dishes before loading?+
Scrape, but do not rinse thoroughly. Auto and sensor cycles measure how dirty the water is to decide how long and hot to run, so a rack of pre-rinsed dishes reads as a light load and gets a short, cool cycle. Modern detergents are also formulated to need some soil to work against.
Everything has a gritty film on it now.+
That is soil being recirculated rather than drained, which points at a clogged filter in the tub floor. Twist it out and clean both the fine mesh and the coarse screen.
Does this answer apply to every GE model?+
No. It is scoped to GDT670S*. GE/GE Profile dishwasher; Dry Boost, bottle jets, UltraFresh and Wi-Fi equipment varies.
What should I record before troubleshooting not cleaning or dirty dishes?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing not cleaning, dirty dishes. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop for grinding, glass, leaks, burning odor or exposed heater damage.
Answer for the exact device and software version shown above.