Direct answer
For the iRobot Roomba i7/i7+, airflow must pass through the head, wand, bin, cyclone and fully dry filters without a leak or blockage. First, power off and remove sections one at a time.
What this covers
- iRobot Roomba i7/i7+ (i7, i7+)
- iRobot Roomba; mapping, obstacle avoidance, self-emptying and mop functions vary.
- The specific fault this record addresses: has weak or no suction
What it does not cover
- ×The same symptom on a different iRobot product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
A filter is clogged or still wet from washing
What separates it Suction has degraded gradually, or dropped sharply right after the filter was last washed and reinstalled before it was fully dry.
How to confirm Remove the filter and test suction briefly without it (never run extended periods without a filter) — a large improvement confirms the filter, and a wet filter should air-dry the full time the manual specifies, sometimes 24 hours or more.
- 2
The airway has a hidden blockage between the nozzle and the bin
What separates it Suction is weak or absent specifically at the floor head, but strong when tested directly at the hose or wand inlet with the head removed.
How to confirm Test suction at each joint working backward from the nozzle — wand, hose, bin inlet — to find exactly where airflow stops improving.
- 3
The bin or dust cup isn't fully sealed
What separates it A hissing sound near a seam, or suction that's uniformly weak everywhere rather than isolated to one point.
How to confirm Check that the bin is fully seated and the release latch is completely closed — a partially seated bin lets air bypass the intended path entirely.
- 4
The cyclone assembly or pre-motor filter is caked with fine dust
What separates it Suction dropped gradually over weeks of use with normal-looking bin filters, especially after vacuuming fine dust, drywall or fireplace ash.
How to confirm Clean the cyclone/separator assembly per the exact model's documented method — this is separate from the washable post-motor filter.
- 5
The motor itself has degraded or failed
What separates it All airway segments test clear and both filters are clean and dry, and suction is still weak or absent.
How to confirm This is the conclusion only once the full airway and both filters are confirmed clear.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether suction is weak everywhere, or specifically weak at one point (nozzle, wand, hose) when tested joint by joint.
- When the filter was last washed, and whether it was fully dried per the manual's stated time before reinstalling.
- What was recently vacuumed — fine dust, ash or drywall dust clog cyclone separators faster than normal household dirt.
Power off and separate sections one at a time
ReversibleNozzle, wand, hose/bin and filters — test suction at each joint working backward.
Inspect each airway segment and the bin seal for blockage or a poor seat
ReversibleA partially seated bin is a common, easy-to-miss cause of uniformly weak suction.
Clear any blockage and reinstall only clean, fully dry filters
ReversibleA damp filter reinstalled early will reproduce weak suction and can damage the motor over time.
Pick up a controlled test line of debris on both hard floor and carpet
ReversibleConfirms the fix across both surface types, since airflow needs differ between them.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- i7, i7+. iRobot Roomba; mapping, obstacle avoidance, self-emptying and mop functions vary.
- Type — ROBOT vacuum
- A ROBOT vacuum with Imprint smart mapping (learns and saves room maps for targeted cleaning) — symptoms are navigation, docking and brushes. The i7+ adds a Clean Base self-empty dock; the plain i7 empties its onboard bin.
- Docking & (on +) self-empty
- 'Won't dock/charge' is dirty contacts, a moved/unplugged dock, or blocked clearance. On the i7+, 'won't empty' is a full Clean Base bag or clogged path.
- Brushes, wheels & sensors
- Two rubber brushrolls, side brush, wheels and sensors — clear hair and wipe sensors if it gets stuck or misses areas. If room-by-room cleaning stops working, the saved map may need re-learning in the app.
- Symptom boundary
- This record covers iRobot Roomba i7/i7+ when it has weak or no suction. A different symptom on the same hardware, or this symptom on a different iRobot product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Stop for a burning smell, unusual heat, liquid ingress, or visible motor damage — these are not filter or blockage issues.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. iRobot Support publishes this as "Poor Pickup: Roomba® e, i, and j series, and Combo 10 Max". iRobot's own poor-pickup/no-suction article, explicitly scoped to e/i/j series and Combo 10 Max — matches this model group exactly. Verified reachable and content-matched via the Browser tool 2026-08-28 after direct fetch was refused. What that article does not carry is the model boundary — it is written for a product line, and i7, i7+ is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
My Roomba i7 stopped cleaning specific rooms on command.+
Room-by-room cleaning relies on the saved Imprint map, so if the home changed (furniture moved, a new area) or the map got corrupted, targeted cleaning can fail. In the app, check the map is intact and the rooms are labelled; you may need to re-run a mapping/training run so it relearns the layout. Also make sure it starts from its home dock, since it orients from there. Clear the brushes and wheels if it is also getting physically stuck.
Suction is fine at the hose but weak at the floor head.+
Test each joint working backward from the nozzle — wand, then hose, then bin inlet — to find exactly where airflow drops. Strong suction at the hose with weak suction at the head isolates the blockage to the wand or head itself, not the motor or filters.
I just washed the filter and suction got worse, not better.+
Check whether it was fully dry before reinstalling — manuals often specify 24 hours or more of air-drying, and a filter reinstalled damp restricts airflow just as much as a dirty one, sometimes more.
Does this answer apply to every iRobot model?+
No. It is scoped to i7, i7+. iRobot Roomba; mapping, obstacle avoidance, self-emptying and mop functions vary.
What should I record before troubleshooting no suction or weak suction?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing no suction, weak suction. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop for burning odor, heat, liquid ingress or motor damage.
Answer for the exact device and software version shown above.