If the Frigidaire FFFW5000 fills slowly or not at all, Frigidaire's checklist is: water supply faucets fully open; the supply adequate (check another faucet in the house and avoid running water elsewhere while the washer fills, since the FFFW5000 needs at least 30 psi); inlet hoses not kinked; hot water at least 120 F; and the door closed. On the FFTW4120 top-loader a fill that takes over an hour raises an error whose checklist adds cleaning the inlet screens, checking for leakage from the tub and closing the lid; Frigidaire's E1 article is titled long fill time.
Differential
Likely causes of “Frigidaire FFFW5000 front-load washer will not fill with water or fills too slowly”, and how to tell them apart
- 1
Faucets not fully open or hoses kinked
What separates it The fill is slow or there is none because the faucets are not fully open or the hoses are kinked
How to confirm Fully open both faucets and straighten the hoses
- 2
Inadequate water pressure
What separates it The fill is slow while other taps are running because the water pressure is inadequate
How to confirm Wait until supply pressure increases; keep other water off during fill
- 3
Clogged inlet screens
What separates it A fill error shows after a long wait because the inlet screens are clogged
How to confirm Disconnect the inlet hoses and clean the inlet screens
- 4
Hot water heater set low
What separates it The warm or hot water is not hot enough because the hot water heater is set low
How to confirm Set the water heater to at least one hundred twenty degrees Fahrenheit
Before you touch a setting
Record this first — changing settings destroys the evidence
- Which faucets are on and the hose condition
- Whether other taps were running while the washer filled
- What the display shows and how long the washer waited
Try in this order
0 of 5 completedOpen the faucets
ReversibleOpen the faucets, by turning both on fully, and straightening the hoses, and then test again to see whether it helped.
Check pressure
ReversibleCheck the pressure, by trying another faucet, and avoid using water elsewhere while the washer fills.
Clean the inlet screens
ReversibleClean the inlet screens, by disconnecting the hoses and rinsing the screens under a tap.
Check the water temperature
ReversibleCheck the water temperature at a nearby faucet with a thermometer, and it should be at least 120 degrees Fahrenheit.
Close the door or lid
ReversibleClose the door or the lid, since the washer will not operate or fill with it open.
Model-specific
What is true of this model and not of its siblings
- Top-load fill-time error
- On the FFTW4120, a fill that takes too long (1 hour) raises an error whose steps are: close the washer lid, fully open the hot and cold faucets, straighten kinked inlet hoses, check supply pressure at other outlets, disconnect the inlet hoses and clean the inlet screens, check for water leaking from the tub and call service if it continues.
- Parts for this problem on the FFFW5000 (RepairClinic, 2026-09-20)
- dispenser valve, ntc/long tube, part number 134959340, at $130.18; water level pressure switch, part number 134762010, at $45.94; coin trap tub to pump hose, part number 134639920, at $88.55.
- Other models this page answers
- These steps also fit the FFTW4120 top-load washer, FLXE52 laundry-center washer.
Stop boundary
When this stops being a self-service repair
- !If the fill error returns after cleaning the screens and confirming supply, call Frigidaire service on 1-800-944-9044
Evidence ledger
Sources behind this answer
The published manual page that ties the FFTW4120SW top-loader to Frigidaire's use and care guide A07504301.
Frigidaire's own owner-support article titles for these three codes.
Parts and list prices as shown on RepairClinic's parts search for this model number on 2026-09-20.
Exact questions
Common questions
Why is my Frigidaire washer filling slowly?+
Faucets not fully open, kinked hoses, low supply pressure, clogged screens or hot water demand elsewhere.
What does a long fill error mean?+
The top-loader's fill took over an hour; Frigidaire's E1 article is titled long fill time.
Should the hot water be hot?+
At least 120 F at a nearby faucet.
Can hot water use elsewhere affect my wash?+
Yes; the hot water system may not support more than one use at a time.