Direct answer
For the LG WashTower WKEX300H washer section, describe the sound by stage and speed before assuming a motor or bearing failure. First, run empty tumble/agitation, drain and spin while recording when the sound begins.
What this covers
- LG WashTower WKEX300H washer section (WKEX300H*)
- WashTower model with center controls; confirm washer versus dryer status.
- The specific fault this record addresses: makes grinding, squealing, clicking or banging noises
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
A foreign object is in the drain pump or between the tub and drum
What separates it A rattling or clicking during drain, or a metallic scraping during spin. Coins, buttons and underwire from bras are the usual objects.
How to confirm On a front-load machine, the drain pump filter is owner-accessible and objects collect there. An object between the outer tub and inner drum is a service repair.
- 2
The tub bearing has failed
What separates it A loud rumbling or roaring during spin that grows worse over weeks, often with the drum feeling loose when rocked by hand, and sometimes accompanied by water appearing under the center of the machine.
How to confirm This is a major repair whose cost often approaches the machine's value — worth knowing before authorising it.
- 3
The shipping bolts were never removed
What separates it Loud banging and hammering during spin on a newly installed or relocated front-load washer.
How to confirm See shaking-vibration — this is the first thing to check on a new installation.
- 4
The drain pump is running against a partial blockage
What separates it A humming or buzzing during the drain phase specifically, with slow or no water movement.
How to confirm See not-draining.
- 5
The drive belt or motor coupling is worn
What separates it Squealing during the wash or spin phase, or a burning rubber odor.
How to confirm This is a service diagnosis and is more common on belt-driven machines.
- 6
Normal operating sounds are being mistaken for faults
What separates it Clicking during fill (inlet valves), a whirring that changes pitch with drum speed (a direct-drive motor), or gurgling at the end of drain.
How to confirm These are normal. A new owner moving from an older belt-driven machine to a direct-drive one often reports the motor's whine as a fault.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- The phase the noise occurs in — fill, wash, drain or spin. This narrows the cause more than the sound description does.
- Whether the noise is present on an empty run as well as a loaded one.
- Whether the noise has developed gradually over weeks, which points at a bearing, or appeared suddenly, which points at a foreign object.
- Whether the drum feels loose or drops when rocked by hand with the machine off.
Run an empty tumble, drain and spin, recording when each sound begins
ReversibleAn empty run separates load noise from machine noise.
Check the drain pump filter for foreign objects
ReversibleCoins, buttons and underwire collect here and cause rattling during drain.
Confirm the shipping bolts were removed on a newly installed machine
ReversibleBanging during spin on a new front-load installation is this until proven otherwise.
Arrange service for a rumbling that worsens over weeks or a drum that feels loose
ReversibleThat pattern indicates a tub bearing, and the repair cost is worth understanding before authorising it.
Confirm the noise is absent on both empty and balanced-load tests
ReversibleVerifies the repair.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- WKEX300H*. WashTower model with center controls; confirm washer versus dryer status.
- Type — WashTower: stacked washer + dryer, one control panel
- A larger-capacity WashTower with the washer below, dryer above, and ONE shared center control panel. As with any WashTower, a control/power fault can affect both halves together, and a centrally shown code may belong to either section — determine washer-versus-dryer first.
- Motor — Direct Drive inverter (no belt)
- Belt-less Direct Drive inverter washer motor; noise/vibration is bearings and balance, not a belt.
- Smart
- ThinQ Wi-Fi with AI-sensing. Washer front-load gasket care for odour; the dryer needs normal lint/vent maintenance.
- Symptom boundary
- This record covers LG WashTower WKEX300H washer section when it makes grinding, squealing, clicking or banging noises. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Stop for metal-on-metal impact, smoke, a burning insulation odor, or a seized drum.
- !A rumbling bearing combined with water under the center of the machine means stop using it — the seal has failed and continued use will damage the drive and the outer tub.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "LG Washer - Troubleshooting Noises During the Cycle". Grinding, squealing, clicking and banging heard during a wash cycle. What that article does not carry is the model boundary — it is written for a product line, and WKEX300H* is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
How do I tell if it's the washer or dryer at fault on my LG WashTower?+
Because the WashTower shares one control panel, note which drum the problem is in and which controls respond. Run each half on its own: start a short wash and, separately, a short dry, and watch which one shows the error or fails to start. A code on the shared display often has a washer or dryer prefix in the manual. Isolating the section first stops you troubleshooting the wrong machine.
There's a loud rumbling during spin that's been getting worse.+
Gradual worsening over weeks, especially with the drum feeling loose when rocked by hand, points at the tub bearing. It is worth getting a repair quote before authorising the work, because on many machines this repair approaches the cost of replacement.
My new washer makes a high-pitched whine during the wash.+
On a direct-drive machine that is usually the motor and is normal — it changes pitch with drum speed. It sounds unfamiliar coming from an older belt-driven washer, which masked the motor noise.
Does this answer apply to every LG model?+
No. It is scoped to WKEX300H*. WashTower model with center controls; confirm washer versus dryer status.
What should I record before troubleshooting grinding or squealing or banging?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing grinding, squealing, banging. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop for metal-on-metal impact, smoke, hot insulation or a seized basket.
Answer for the exact device and software version shown above.