Direct answer
For the LG WashTower WKEX300H washer section, verify both water supplies, inlet screens, hose routing and the selected cycle before treating the inlet valves or pressure system as failed. First, open both faucets fully and note whether hot, cold or both are missing.
What this covers
- LG WashTower WKEX300H washer section (WKEX300H*)
- WashTower model with center controls; confirm washer versus dryer status.
- The specific fault this record addresses: will not fill with water or fills too slowly
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
One or both supply faucets are closed or only partly open
What separates it No fill at all, or the machine fills only with cold or only with hot. Each temperature comes from its own hose and its own valve, so a single closed faucet produces a partial rather than total failure.
How to confirm Open both faucets fully and note which temperature is missing — that identifies which side of the supply to inspect.
- 2
The inlet screens are clogged with sediment
What separates it Filling is very slow rather than absent, often worse on one temperature than the other, and the machine may time out and report a fill fault.
How to confirm With both faucets closed and power disconnected, the small screens in the inlet valve ports are owner-cleanable on most machines. Sediment collects here after plumbing work or in hard-water areas.
- 3
A supply hose is kinked behind the machine
What separates it Slow or absent fill that began after the machine was moved, or after something was stored behind it.
How to confirm Pull the machine out far enough to see the full hose run rather than reaching blindly behind it.
- 4
The door or lid is not locked, so filling never starts
What separates it The cycle appears to start but no water enters and no fault appears immediately. A front-load washer cannot fill until the door locks, because the water level sits above the door opening.
How to confirm Watch for the lock indicator before the fill phase. If it never appears, this is a door-lock problem rather than a water-supply one — see door-lid-not-locking.
- 5
The machine is filling correctly and the level only looks wrong
What separates it Water enters but never submerges the load, on a high-efficiency machine. This is by far the most common reason people report a fill problem on a modern washer.
How to confirm Watch whether every item becomes thoroughly wet and turns over during the wash action. If it does, the machine is working as designed — see not-level-water-too-low.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether no water enters at all, or water enters slowly, or water enters normally but to a level that looks too low.
- Which temperature is missing — hot, cold, or both — since each has its own hose, faucet and valve.
- Whether the door or lid lock indicator appears before the fill phase should begin.
Open both faucets fully and note whether hot, cold or both are missing
ReversibleThis identifies which supply side to inspect and rules out the most common cause in seconds.
Disconnect power and close both faucets before inspecting hoses and inlet screens
ReversibleNever work on an inlet valve with water pressure or power present.
Clear kinks and clean the owner-accessible inlet screens
ReversibleSediment in these screens is a common cause of slow filling, particularly after plumbing work or in hard-water areas.
Confirm the door or lid actually locks before the fill phase
ReversibleA front-load washer that cannot lock will never fill, and that is a lock fault rather than a supply fault.
Run a normal fill and confirm the water stops at the expected level
ReversibleOn a high-efficiency machine, the expected level is well below the top of the load.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- WKEX300H*. WashTower model with center controls; confirm washer versus dryer status.
- Type — WashTower: stacked washer + dryer, one control panel
- A larger-capacity WashTower with the washer below, dryer above, and ONE shared center control panel. As with any WashTower, a control/power fault can affect both halves together, and a centrally shown code may belong to either section — determine washer-versus-dryer first.
- Motor — Direct Drive inverter (no belt)
- Belt-less Direct Drive inverter washer motor; noise/vibration is bearings and balance, not a belt.
- Smart
- ThinQ Wi-Fi with AI-sensing. Washer front-load gasket care for odour; the dryer needs normal lint/vent maintenance.
- Symptom boundary
- This record covers LG WashTower WKEX300H washer section when it will not fill with water or fills too slowly. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Close both faucets immediately for an uncontrolled fill, an overflow, or a leaking hose — do not wait to finish diagnosing.
- !Never probe or disassemble a live inlet valve with power connected.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "LG Washer - Troubleshooting Fills Too Slow / Does Not Fill". LG's own article for both halves of the symptom — no fill at all and abnormally slow fill. What that article does not carry is the model boundary — it is written for a product line, and WKEX300H* is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
How do I tell if it's the washer or dryer at fault on my LG WashTower?+
Because the WashTower shares one control panel, note which drum the problem is in and which controls respond. Run each half on its own: start a short wash and, separately, a short dry, and watch which one shows the error or fails to start. A code on the shared display often has a washer or dryer prefix in the manual. Isolating the section first stops you troubleshooting the wrong machine.
The washer only fills with cold water, never hot.+
Each temperature comes from its own hose, faucet and inlet valve, so a missing hot fill points at the hot side specifically — check that the hot faucet is fully open and that the hot inlet screen is not clogged with sediment.
Barely any water goes in — is it broken?+
On a high-efficiency washer this is usually normal. These machines are designed not to submerge the load. What matters is whether every item becomes thoroughly wet and turns over during the wash action; if it does, the fill level is correct even though it looks wrong.
Does this answer apply to every LG model?+
No. It is scoped to WKEX300H*. WashTower model with center controls; confirm washer versus dryer status.
What should I record before troubleshooting not filling or slow fill or no water?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing not filling, slow fill, no water. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Close the faucets for an uncontrolled fill or leak; never probe a live inlet valve.
Answer for the exact device and software version shown above.