On the covered Amana dryer, F1 E5 means the main control board or the wiring that feeds it reported a fault First, touch Power, pick a cycle and hold Start. Then: unplug the dryer, check the control board connectors, and replace the board only if F1 E5 comes back.
Differential
Likely causes of “Amana dryer code F1 E5”, and how to tell them apart
- 1
The main control board or its feed wiring
What separates it F1 E5 appears and the drum will not start
How to confirm Unplug the dryer and see whether it clears
- 2
A worn power connection at the board
What separates it The code comes and goes with vibration
How to confirm A technician checks the power plug at the board
- 3
A failing control board
What separates it F1 E5 returns after every reset
How to confirm A board that fails every reset is replaced
- 4
A power cord or receptacle problem
What separates it F1 E5 with a warm plug or a loose fit in the outlet
How to confirm A poor connection at the cord starves the board of steady power
Before you touch a setting
Record this first — changing settings destroys the evidence
- Whether the drum turns
- Whether the code returns after five minutes unplugged
- Whether the dryer shakes in use
- The model number
Try in this order
0 of 7 completedWhat to do first
Reversibletouch Power, pick a cycle and hold Start.
Correct only the documented fault domain
ReversibleUnplug the dryer, check the control board connectors, and replace the board only if F1 E5 comes back. Amana documents one check for this code — did you receive a F1E5 alert — so confirm that before treating anything else as the cause.
Touch Power, choose a cycle, hold Start
ReversibleWhirlpool's own page for F1 E5 starts with touching Power, selecting a cycle and holding Start/Pause.
Unplug the dryer
ReversibleIf that fails, unplug it for five minutes.
Replace the board only if needed
ReversibleA technician replaces the control board when the reset does not hold.
Look at the plug and outlet
ReversibleUnplug the dryer and look at the cord prongs and the outlet for burn marks or a loose fit. A heated plug is a hazard and needs an electrician before anything else.
Compare it with F1 E3 on the same dryer
ReversibleIf you have seen F1 E3 before and now see F1 E5, the board is reporting more than one internal check failing. That pattern is a stronger sign of a failing control than a single code that clears after a reset.
Model-specific
What is true of this model and not of its siblings
- Shown as
- F1 E5.
- Part named
- Main control board.
Stop boundary
When this stops being a self-service repair
- !Do not run a dryer that shows a control fault unattended
- !Book service if F1 E5 returns
Evidence ledger
Sources behind this answer
Exact questions
Common questions
What does F1 E5 mean on a Amana dryer?+
the main control board or the wiring that feeds it reported a fault
Is it the user interface?+
On Whirlpool's page the user interface can also be named, so a technician checks both.
How long should I wait before calling?+
After one reset that does not hold.
What is the difference between F1 E5 and F1 E1 on a dryer?+
Whirlpool groups F1 E1, F1 E3, F1 E4 and F1 E5 as control faults. The last digit marks which internal check was involved.
Why unplug for five minutes?+
A longer wait lets the board's memory fully discharge so it starts from a clean state.
My dryer shows F1 E5 after it was moved. Why?+
A move can loosen the main board's connectors. Reseating them with the dryer unplugged is the cheap check to do before the board is replaced.
Should I keep trying to start it?+
A few attempts after a reset are fine. Repeated starts that always fail point to the board.