On the covered Amana range, F5 E1 means the self-clean door latch will not lock or unlock, or its switch or wiring reported a fault First, turn the breaker off for one minute and back on. Then: check the latch motor and switch wiring and replace the latch assembly, which carries the motor and switch together.
Differential
Likely causes of “Amana range code F5 E1”, and how to tell them apart
- 1
The self-clean latch will not lock
What separates it F5 E1 shows when you start a clean cycle
How to confirm Watch whether the lock lever moves when the cycle begins
- 2
The latch will not unlock after cleaning
What separates it The door stays locked after the oven cools
How to confirm Wait for the oven to cool and try the latch again
- 3
The latch motor or switch assembly has failed
What separates it A power reset does not clear the code
How to confirm The motor and switch are one assembly on these ranges
Before you touch a setting
Record this first — changing settings destroys the evidence
- Whether the door is locked or unlocked now
- Whether a self-clean was running
- Whether the code returns after a reset
- The model number
Try in this order
0 of 6 completedWhat to do first
Reversibleturn the breaker off for one minute and back on.
Correct only the documented fault domain
ReversibleCheck the latch motor and switch wiring and replace the latch assembly, which carries the motor and switch together. A power reset is the whole of what Amana publishes for this code: remove power for 1 minute, restore it, and watch whether the code returns.
Reset at the breaker
ReversibleSwitch the range breaker off for one minute and on again, then watch the display.
Lock and unlock the door
ReversibleAfter the oven is cool, run the lock through its movement and see whether it completes.
Look at the latch assembly
ReversibleIf nothing seems loose or damaged, the whole latch assembly is replaced, because the motor and switch come together.
Separate a lock fault from a switch fault
ReversibleRun a short self-clean setup, listen at the start for the motor, and look at the lever. A motor that runs and stops short of its mark is a worn latch; a motor that never runs may be a wiring or board output problem, which a technician can tell apart with a meter.
Model-specific
What is true of this model and not of its siblings
- Shown as
- F5 E1.
- Part named
- Main oven door latch assembly.
- When it appears
- At the start or end of a self-clean cycle, when the latch is asked to lock or unlock.
Stop boundary
When this stops being a self-service repair
- !Never pry a locked oven door
- !Book service if the door stays locked on a cool oven
Evidence ledger
Sources behind this answer
Exact questions
Common questions
What does F5 E1 mean on a Amana range?+
the self-clean door latch will not lock or unlock, or its switch or wiring reported a fault
Why did my oven lock itself?+
Self-clean locks the door by design; the code is the control telling you the lock did not finish.
Can I replace only the motor?+
On these ranges the motor and switch are sold together as the latch assembly.
Can I skip self-clean to avoid F5 E1?+
Yes. Hand-cleaning the oven with the door unlocked avoids the latch cycle altogether, though the code itself stays until the latch is repaired.
Is the oven safe to bake in while F5 E1 shows?+
Many ovens still bake, but a door that cannot lock can also fail to unlock after a hot cycle. Avoid the clean cycle until the latch is fixed.
What is the Amana F5 E1 latch motor made of?+
It is a small gear motor with a switch built into the same housing, which is why the whole assembly is replaced.
Can I open the door by hand while F5 E1 shows?+
Do not force it. Let the oven cool completely, switch the breaker off for a minute, switch it on and try the door again. If the door stays locked after that, book service rather than prying at the latch.