Expanded exact-code directory
Dacor dishwasher error codes
Dacor dishwasher indicators as Sears PartsDirect (parts and repair reference) lists them, each with its meaning and the first safe check.
- cycle-stops-followed-by-3-water-in-the-base-pan-water-leakListed as water in the base pan (water
- f2-water-inlet-valve-won-t-shut-keepsListed as water inlet valve won't shut (keeps
- f3-low-inlet-water-pressure-long-fillListed as low inlet water pressure (long fill
Every code
Every Dacor dishwasher code: what it means and what to do
- cycle-stops-followed-by-3-water-in-the-base-pan-water-leak
- f2-water-inlet-valve-won-t-shut-keeps
- f3-low-inlet-water-pressure-long-fill
- f4-no-signal-from-the-water-pressure
- f9-heater-failure
- three-long-beeps-and-red-failed-to-drain
Dacor dishwasher code cycle-stops-followed-by-3-water-in-the-base-pan-water-leak
Listed as water in the base pan (water leak).
Unplug the dishwasher or shut off the house circuit breaker to disconnect electrical power. Remove the lower access panel and examine the bottom dishwasher components to find the leak. Replace the leaking components. Remove the water from the base pan of the dishwasher. Parts named: bottom dishwasher components.
Dacor dishwasher code f2-water-inlet-valve-won-t-shut-keeps
Listed as water inlet valve won't shut (keeps filling).
Unplug the dishwasher or shut off the house circuit breaker to disconnect electrical power. If the dishwasher continues to fill, replace the water inlet valve. If filling stops when you disconnect power, replace the electronic control board. Parts named: water inlet valve, Electronic control board.
Dacor dishwasher code f3-low-inlet-water-pressure-long-fill
Listed as low inlet water pressure (long fill time).
If the water supply cut-off valve for the dishwasher is fully open and the dishwasher still fills slowly, shut off the water supply, unplug the dishwasher, disconnect the fill line and check whether the screen in the water inlet valve is clogged. If it's clogged, replace the water valve-don't just clean the screen, because debris could fall into the valve body, prevent the valve from closing, and cause flooding. Check the wiring connections on the inlet water valve and secure any loose connections. If the water valve won't open when activated, replace it. Parts named: water inlet valve.
Dacor dishwasher code f4-no-signal-from-the-water-pressure
Listed as no signal from the water pressure switch.
Unplug the dishwasher or shut off the house circuit breaker to disconnect electrical power. Remove the lower access panel. Check wire harness connections. on wire harness for the water pressure switch. If the wire connections are okay, replace the water pressure switch. Parts named: water pressure switch, Wire harness.
Dacor dishwasher code f9-heater-failure
Listed as heater failure.
Have a service technician examine and repaired the inline flow-through heater. Parts named: heater.
Dacor dishwasher code three-long-beeps-and-red-failed-to-drain
Listed as failed to drain.
Press Cancel twice to reset. If the error code reappears, clear clogs from the sink drain. Unplug the dishwasher and clear clogs from the dishwasher drain hose and drain pump. If the drain hose or drain pump is damaged, replace it. Parts named: drain hose, Drain pump.
Sears PartsDirect (parts and repair reference) — Dacor dishwasher error codes
Dacor dishwasher codes and first checks
A Dacor dishwasher reports problems on its display or with flashing lights, and a code usually refers to water in, water out, the heater or a sensor. Before anything else, check that the water tap is open, the filter at the bottom of the tub is clean and the drain hose has no kink. A door that is not fully latched also stops a cycle, so close it firmly and look for anything caught in the seal.
Switch the dishwasher off at the breaker for a minute and restart it with a short cycle. Heater, pump and control faults, and anything involving the water inlet valve, need a service technician, and Dacor service will ask for the model and serial number from the data plate inside the door.
Dacor's dishwashers are built to be fitted in premium kitchens with panels, which can affect door balance and the way the door closes. If the door does not latch, check that the panel and its springs have been adjusted for the weight, as a heavy panel can pull the door open. Water faults often follow installation, so check the supply valve and the drain loop. A technician who knows the product can adjust the door tension.
Dacor's dishwashers are fitted behind custom panels in many kitchens, and the panel's weight changes how the door behaves. If a door feels heavy or does not stay closed, the springs may need adjusting. If the door is hard to latch, check that the panel is not rubbing the cabinet. These installation details are often the cause of a door code, so a check by the installer can save a service call.
The wash system uses a pump, a heating element and spray arms, and the codes name them. A heating code usually means that the element or its thermostat has failed, which leaves dishes cold and wet. A pump code means that the pump motor or its wiring has a fault, and a leak code means that the sensor in the base found water. Do not open the base to look, since the pan may hold live parts.
Premium dishwashers often have several cycles and options that change times and temperatures. If a cycle seems to take very long, check that you have not selected an extended or sanitizing option. Use detergent suited to the water and keep the filter clean. If a code appears right after installation, tell the installer, since a hose or a connection may be at fault.
How do I reset a Dacor dishwasher?
Switch off the breaker for a minute, restore power and run a short cycle. If the code returns, call for service.
Why does my dishwasher door not latch?
The door springs may need adjusting for the panel's weight.