Electrolux dishwasher error codes

Electrolux dishwasher codes

Electrolux dishwashers show codes such as CL or Cd for a door that is not closed and latched, and other codes for fill, drain and heater faults. Close the door firmly and look for anything in the seal, then check the water tap, the filter and the drain hose. Soap suds in the tub can also cause errors, so use the right amount of dishwasher detergent only.

Reset the power at the breaker for a minute and run a short cycle. A code that returns points to the inlet valve, the pump or the control and should be checked by a technician.

Electrolux dishwashers are often built into suites with matching appliances, and they use the same family of electronic controls. If the display is dark, check the breaker and the connection first. A display that works but a cycle that will not start may have a door switch fault. Check that the door closes fully, and look for an item caught in the seal. Leave the door ajar after the cycle to dry the interior, and run a cleaner monthly.

Electrolux dishwashers are often installed in a suite with matching appliances, and they share design features with sister brands. The codes in this table cover the water inlet, the drain, the heating, the door and the control. A display that stays dark after installation usually has a power problem, not a fault in the dishwasher: check the breaker and the connection under the sink.

Water quality changes how an Electrolux dishwasher performs. In hard water, scale builds on the element and the spray arms, and a white film appears on glasses. Use a rinse aid and, if the model has a water softener, add dishwasher salt. Clean the filter assembly regularly, and run an empty cycle with a cleaner every month or two. Check the spray arms for blocked holes and that they spin freely.

If the door will not latch, look for an item blocking it, a dish rack out of place or a door that sags. If the dishwasher stops mid-cycle, check for an inlet or drain code and test the supply valve under the sink. Leave the door ajar after the cycle to let the interior dry. The rating plate on the edge of the door has the model, product number and serial that Electrolux support asks for.

Electrolux dishwashers often sit in a suite with an oven and a refrigerator from the same maker, and the controls share a visual style. The display on the dishwasher itself reports faults, and some models also report through a phone app. If the display shows a code and the app shows something different, trust the display, since the app can lag behind. Note both when you call.

Cleaning and care affect how often a code appears. Wipe the door seal and the edge of the tub with a damp cloth after each cycle, rinse the filter assembly every few weeks and run a cleaner monthly. Use the detergent form the manual recommends, since a pod in a machine set for powder can leave residue that blocks the dispenser. If you have hard water, keep the rinse aid and any salt compartment topped up, as scale on the heater and the sensors causes temperature and drain codes.

When a dishwasher stops mid-cycle, open the door and look at the water level in the bottom of the tub. Standing water points to a drain problem, an empty tub points to an inlet problem and a dry, cool machine points to a power or control problem. Check the breaker and the isolating switch under the sink before you call, and have the model, product number and serial ready from the rating plate on the door's edge.

Loading is the other quiet cause. Put the dirtiest items facing the center, keep bowls tilted so that water runs off and avoid nesting spoons. Do not let any item block the spray arms or the detergent door, and do not overload the lower rack, which leaves the top rack in shadow. After loading, spin each spray arm by hand to check that it moves freely. A dishwasher that is loaded properly cleans well on a shorter cycle and uses less energy, so a code that appears for an overloaded machine goes away on its own.

Many Electrolux dishwashers include a half-load or a zone option for small loads, and a quick cycle for lightly soiled dishes. These save water and energy, but they do not suit heavily soiled pans. If dishes come out dirty after a short cycle, use the normal program, and run the machine at night when the hot water in your home is at its best, since a cold supply lengthens the heating stage.

A dishwasher that has been installed under a counter next to a hob or an oven can run into heat problems. The cabinet's side panels and the dishwasher's own insulation should keep heat away from the tub, but a poorly fitted filler panel or a missing insulation blanket lets heat in and affects drying and the plastic parts. If the dishwasher seems very hot to the touch on its sides during or after a cycle, tell the installer and check that the insulation that came with it was fitted.