On the covered Whirlpool front-load washer, F4 E0, F4 E1, F03, F23, F06, F61, F62, F63, F64, F65 means the heating element, or on a steam model the steamer, has failed First, unplug the washer and check the wiring to the heating element.
Differential
Likely causes of “Whirlpool front-load washer code F4 E0, F4 E1, F03, F23, F06, F61, F62, F63, F64, F65”, and how to tell them apart
- 1
A broken heating element (F03 or F4 E0)
What separates it The wash water does not warm and the code appears at a heated step
How to confirm The Duet HE table says F03 means the element has an internal short circuit; unplug the washer and replace the element
- 2
A heating element circuit failure (F23)
What separates it The element looks intact but its circuit still reports a failure
How to confirm Unplug the washer, check the harness between the element and the main board, then measure the element; the Duet Steam table says about 15 ohms is expected and infinite resistance means the element is broken
- 3
A steamer or steam valve failure on a steam model (F8 E0, F06, F61 to F65)
What separates it A steam cycle fails and the code is one of the steamer codes
How to confirm Check the supply hoses and the valve screen for F8 E0, and the harness and steamer board for F06, F61, F62, F63 and F64
Before you touch a setting
Record this first — changing settings destroys the evidence
- The exact display: F4 E0, F4 E1, F03, F23, F8 E0, F06 or F61 to F65
- Whether the washer is a steam model
- Whether the code appears on a steam or a hot cycle
Try in this order
0 of 6 completedWhat to do first
ReversibleUnplug the washer and check the wiring to the heating element.
Correct only the documented fault domain
ReversibleTest the element with a meter; replace it only if it reads open.
Reset and retry once
ReversibleWhirlpool's F4 E1 page gives only the 5-minute reset. If the code returns, it is a real fault.
Check the element wiring
ReversibleThe Duet Alpha table says to unplug the washer and check the wiring going to the water-heating element and, if the wiring is okay, to replace the heating element. The Duet Steam table says to reconnect any loose wire or replace the harness if damaged.
Measure the element
ReversibleThe Duet Steam table says to measure the resistance with a multimeter: about 15 ohms is normal, and infinite resistance means the element is broken and should be replaced.
Work through the steam codes
ReversibleFor F8 E0 the Duet Alpha table says to check the supply hoses for kinks, check the valve screen for restriction and replace the steam valve if defective. For F06 and F63 it says to check the wiring between the steamer and its control board, then replace the steamer; F61 and F65 point to the steamer control board wiring, F62 to a failed relay on the steamer board and F64 to the inlet water valve assembly.
Model-specific
What is true of this model and not of its siblings
- Displayed as
- F4 E0, F4 E1, F03, F23, F8 E0, F06 or F61 to F65, by platform.
- Meter reading
- About 15 ohms through the heating element (Duet Steam table).
- Parts named by the service tables
- Heating element; steam valve; steamer; steamer electronic control board; inlet water valve assembly; wire harness.
Stop boundary
When this stops being a self-service repair
- !Unplug the washer before you measure the heating element or open any panel, because the element carries line voltage
- !Do not run a heated cycle again until the element is proved sound, and do not test with the washer plugged in
Evidence ledger
Sources behind this answer
Where the manufacturer's article stops. The 15 ohm figure is the Duet Steam table's own; other platforms may differ.
Exact questions
Common questions
What does F4 E0, F4 E1, F03, F23, F06, F61, F62, F63, F64, F65 mean on a Whirlpool front-load washer?+
the heating element, or on a steam model the steamer, has failed
What resistance should the element read?+
The Duet Steam table says about 15 ohms; infinite resistance means it is broken.
What do the F6x codes mean?+
They are steamer faults on the Duet Steam: F61 and F65 a steamer communication failure, F62 a steamer control board failure, F63 a steamer failure, F64 a steamer inlet valve failure and F06 a steamer failure.
Does the compact use F23 for the element?+
No. On the compact table F23 is a water level pressure switch failure; check your style.