Direct answer
For the TP-Link Deco XE75 mesh, every cable pair, wall jack, switch and port must negotiate the intended speed. First, inspect negotiated speed and connect a known Cat5e+ cable directly.
What this covers
- TP-Link Deco XE75 mesh (Deco XE75)
- TP-Link router/Deco; EasyMesh/Deco controller, Wi-Fi generation, HomeShield and Ethernet ports vary.
- The specific fault this record addresses: Ethernet link is limited to 100 Mbps or disconnects
What it does not cover
- ×The same symptom on a different TP-Link product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The cable is a low category or is damaged
What separates it One run is slow or drops while others are fine, or the cable is old, kinked or thin.
How to confirm Swap in a known-good Cat5e or better cable of adequate rating for the speed you expect; a marginal or damaged cable caps or destabilises a wired link.
- 2
The port negotiated a lower speed than expected
What separates it The link works but at a fraction of the expected rate, and the port/link light or status shows a lower speed.
How to confirm Check the negotiated link speed on both ends; a gigabit device that comes up at 100 Mbps usually has a cable, port or auto-negotiation fault on that run.
- 3
A specific port is failing
What separates it Moving the same cable and device to another port restores full speed.
How to confirm Test the run on a different port; a fault that stays with one port and not the cable or device is the port.
- 4
The other device or its adapter is the limit
What separates it One computer or device is slow on a wire while another reaches full speed on the same port and cable.
How to confirm Compare a second device on the identical port and cable to separate the port from the client's own adapter or configuration.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- The negotiated link speed shown on both ends of the slow run.
- Whether the problem follows the cable, the port, or the device when each is swapped.
- The cable's category rating and its physical condition.
Swap in a known-good adequately-rated cable
ReversibleA bad or low-category cable is the most common wired bottleneck.
Read the negotiated link speed on both ends
ReversibleA gigabit link coming up at 100 Mbps points at the cable, port or negotiation.
Move the run to another port to isolate a failing port
ReversibleIf the problem stays with the port, the port is the fault.
Test a second device on the same port and cable
ReversibleSeparates the network hardware from the client's own adapter.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- Deco XE75. TP-Link router/Deco; EasyMesh/Deco controller, Wi-Fi generation, HomeShield and Ethernet ports vary.
- Wi-Fi 6E tri-band MESH
- A Wi-Fi 6E (AXE) Deco mesh adding 6 GHz. Note the 6 GHz band is often used as the dedicated backhaul, so client 6 GHz access may be limited by design. Units cover a large home; a weak room means a node is too far.
- Mesh backhaul
- A node offline/slow is usually wireless backhaul — place within range or wire it. It is 6E, not Wi-Fi 7.
- Managed by Deco app only
- Managed through the Deco app (no web admin).
- Symptom boundary
- This record covers TP-Link Deco XE75 mesh when it Ethernet link is limited to 100 Mbps or disconnects. A different symptom on the same hardware, or this symptom on a different TP-Link product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Do not force a fixed speed/duplex to mask a bad cable — replace the cable and let the link auto-negotiate cleanly.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. TP-Link publishes this as "TP-Link Ethernet Not Working? Wired and Wi-Fi Fixes". TP-Link's wired-port article for an Ethernet link that will not come up or negotiates low. Probed 2026-08-21: title-verified. What that article does not carry is the model boundary — it is written for a product line, and Deco XE75 is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
Why can't my devices use the 6 GHz band on my Deco XE75?+
On many Deco 6E systems the 6 GHz band is dedicated to the mesh backhaul (the node-to-node link) rather than offered to client devices, so your phone or laptop may not be able to join a 6 GHz network even if it supports one — that is a design choice, not a fault. Client devices use the fast 5 GHz band while 6 GHz keeps the backhaul clear. Check the Deco app's band settings to see how 6 GHz is allocated on your system.
My wired connection is slower than my Wi-Fi.+
That almost always means the wired run negotiated a low speed or has a marginal cable. Check the link speed shown on both ends — a gigabit device coming up at 100 Mbps is the tell — then swap in a known-good Cat5e-or-better cable, and try another port. Whichever swap restores full speed identifies the fault: the cable, the port, or the device's own adapter.
Does this answer apply to every TP-Link model?+
No. It is scoped to Deco XE75. TP-Link router/Deco; EasyMesh/Deco controller, Wi-Fi generation, HomeShield and Ethernet ports vary.
What should I record before troubleshooting 100 Mbps or Ethernet?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing 100 Mbps, Ethernet. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop for wet, pinched, hot or damaged cabling/equipment.
Answer for the exact device and software version shown above.