Exact model-family answer directory
Samsung DW80R7060 dishwasher troubleshooting
Samsung DW80R7060 dishwasher (DW80R7060*): where the DW80R7060 sits; the AutoRelease door; stormWash; codes; the detergent dispenser; heated drying, and a fix for each symptom below.
- Where the DW80R7060 sitsThe DW80R7060 is a Samsung dishwasher with StormWash jets, a third rack, heated drying and the AutoRelease Dry door that opens a little at the end of the cycle. It has a stainless tub.
Confirm the model first
Which units this covers, and how to tell yours is one of them
- Model numbers and patterns
- DW80R7060*
Published specification
What is true of this model and changes how you fix it
- Drying — heated + AutoRelease doorHeated drying plus AutoRelease Dry auto-opening door in the last minutes; intentional.
- Wash & racksStormWash and a 3rd rack; stainless tub.
- CodesLC = leak sensor; drain codes point to the filter and drain hose. Filter and lower spray-arm clogs cause most poor-cleaning complaints.
- The AutoRelease doorThe door opens by itself in the last minutes of the cycle to let steam out. That opening is intentional and helps drying, so a door that is ajar at the end is the system working.
- StormWashJets in the spray arms and rotating nozzles wash the lower rack and the third rack. A clogged filter or a blocked nozzle is the usual reason a part of the load stays dirty.
- CodesLC means the leak sensor has detected water; drain codes point at the filter and drain hose; other letter codes name the fill, door and heater.
- The detergent dispenserThe dispenser door opens during the wash to release detergent. If it does not open, or detergent stays in it, the cause is usually something blocking the door, a damp or caked dispenser or a lid that did not close.
- Heated dryingA heating element and the AutoRelease door dry the load; rinse aid improves results.
- The AutoRelease doorIn the last minutes of the drying phase the door pops open a few centimetres on its own. Leave it alone: closing it by hand during the phase interrupts the drying, and the spring will push it open again.
- A leak sensor messageAn LC message means the base sensor has detected water. Switch off, check the door seal, the supply connection and the drain hose for the source, and dry the base before restarting, since the sensor will not clear until the base is dry.
- WaterWall and the spray armThe WaterWall spray moves along the back of the lower rack. A tall item that blocks its path leaves a strip of dishes dirty, and checking that nothing in the rack obstructs the arm helps.
- Drying and AutoReleaseThe door opens slightly at the end to let steam out. Closing it by hand cuts the drying, so leave it open until the dishes are cool and dry.
- Filter and rinse aidClean the filter monthly and keep the rinse-aid tank filled. These two steps prevent most spots on glasses and a dishwasher that smells.
Where these figures were read. image-us.samsung.com/SamsungUS/home/home-appliances/dishwasher/11-02-2020/DW80R7060_Spec_Sheet_Final.pdf (Samsung spec sheet) (StormWash, AutoRelease Dry, 3rd rack)
Manufacturer support for this product line. Samsung Support — Samsung washing machine information and error codes. Samsung's own washer troubleshooting and error-code article; covers filling, draining, spin and unbalanced-load conditions.
Also read for this model. Samsung Support — Samsung dishwasher support.
Exact questions
Questions that only have an answer for the Samsung DW80R7060 dishwasher
My Samsung DW80R7060 isn't cleaning the bottom rack well.+
Clean the filter at the bottom of the tub first — a clogged manual filter is the top cause of poor cleaning. Then check the lower spray arm spins freely and its holes are not blocked by debris, and do not let large items block its rotation. Scrape (do not pre-rinse) dishes, use fresh detergent, and run the hot water at the sink briefly before starting so the dishwasher fills with hot water.
Why does the door open at the end?+
AutoRelease Dry opens it to release steam.
What does LC mean?+
The leak sensor has detected water.
Why is the dispenser door stuck?+
Something blocks it or the dispenser is caked.
Where is the model label?+
On the inside edge of the door.