The Samsung DVE45T6000 dries by sensing moisture in the load: the Sensor Dry icon shows on NORMAL, HEAVY DUTY, BEDDING, ACTIVEWEAR, DELICATES and PERM PRESS, and the dryer stops when the load reaches the dryness level, so the time on the display changes as it goes. If clothes come out damp or the time keeps growing, the manual points at airflow first, then load size, then the sensor. C1 means the dryer detects items inside the drum or an error on the dry sensor, so run the cycle with a load of the right size and clean the sensor bars if a film has formed.
Differential
Likely causes of “Samsung dryer sensor cycle ends too early or runs too long”, and how to tell them apart
- 1
A film on the sensor bars from fabric softener or lint
What separates it Clothes are damp at the end or the cycle stops early
How to confirm Wipe the sensor bars inside the drum with a damp cloth and a mild cleaner
- 2
Too small or too large a load for the sensor to read
What separates it One or two items dry unevenly or the time keeps extending
How to confirm Add a few towels to a small load, or remove items from a large one
- 3
Restricted airflow slows the drying so the sensor keeps the cycle going
What separates it The time on the display keeps rising and the load stays damp
How to confirm Clean the lint filter and run the Vent Blockage Test
- 4
A dry sensor fault, shown as C1
What separates it C1 shows even with an empty drum because of a dry sensor fault
How to confirm Remove the load, check again, and contact service if C1 continues
Before you touch a setting
Record this first — changing settings destroys the evidence
- Which cycle and dryness level you selected
- How large the load was and whether it was mixed weights
- Whether C1 or a check code appeared
Try in this order
0 of 5 completedConfirm the cycle is a sensor cycle
ReversibleThe Sensor Dry icon appears when the dryer operates a cycle that senses internal humidity. Time Dry, Quick Dry and Air Fluff do not use the sensor, so their times are the times you set.
Check the dryness level
ReversiblePress Dryness to choose from five levels, Less to More. For bulky or heavy loads the manual says to choose More; items that hang dry can use Less.
Clean the lint filter
ReversibleThe Clean Lint Filter icon reminds you after every load. A clogged filter is the most common reason sensor cycles run long or finish damp.
Balance the load
ReversibleThe manual says heavy and light items should be dried separately, and that one heavy item with light ones may not finish when the rest reaches the dryness level.
Use Damp Alert
ReversibleWith mixed fabrics, the Damp Alert light blinks when the load's average dryness reaches about 80 percent, so you can take out quick-drying items and let the rest continue.
Model-specific
What is true of this model and not of its siblings
- Sensor cycles in the cycle chart
- Normal (cottons, work clothes, linens, mixed loads), Heavy Duty (jeans, corduroys, heavy work clothes), Bedding (blankets, sheets, comforters, pillows), Activewear (maximum 4 lb), Sanitize (very dry, not adjustable), Delicates and Perm Press are sensor cycles; Quick Dry, Time Dry and Air Fluff are timed. Sanitize and Activewear do not offer the dry-level or Damp Alert options.
- Other models this page answers
- These steps also fit models DVE53BB8700, DVE50BG8300, DVG53BB8700, DVG50BG8300, DVG45T6000, DV45K6500, DV42H5000.
Stop boundary
When this stops being a self-service repair
- !If C1 appears with an empty drum after cleaning the sensor bars, contact a Samsung service center
- !If clothes stay damp with a clean filter and duct, stop guessing and contact service
Evidence ledger
Sources behind this answer
Exact questions
Common questions
Why does the time on the display change?+
Sensor Dry decides the drying time from the moisture it senses, so the time changes with the type and amount of laundry.
Which cycles use the sensor?+
Normal, Heavy Duty, Bedding, Activewear, Delicates and Perm Press. Time Dry, Quick Dry and Air Fluff are timed.
Is a damp seam normal?+
The manual says seams and pockets may not be completely dry when the rest of the load has reached the selected level. Choose a higher dryness level.
Can Eco Dry lengthen a sensor cycle?+
Yes. With Eco Dry on, drying can take up to three times as long depending on temperature and load.
What is Damp Alert?+
A light that blinks when the average dryness of a mixed load reaches about 80 percent, so you can pull out items you do not want fully dry.
Can I change the temperature on a sensor cycle?+
Temperature can be adjusted only in the Time Dry cycle.
What load size does the manual recommend?+
One wash load equals one dryer load. A large load fills the drum about three quarters, a medium about half.