On the covered Whirlpool range, Probe, Insert Probe, 3D31, 3D32, 3D41, F3 E4, F4 E1 means the control is looking for the meat probe and cannot read it First, push the probe fully into its jack and into the food.
Differential
Likely causes of “Whirlpool range code Probe, Insert Probe, 3D31, 3D32, 3D41, F3 E4, F4 E1”, and how to tell them apart
- 1
A meat probe that is not fully seated in its jack
What separates it The display shows Probe or Insert Probe and the oven does not start a probe cycle
How to confirm Push the probe plug all the way into the jack; Whirlpool says the control is looking for an input from the probe
- 2
A probe not inserted into the food
What separates it The probe is in the jack but not in the meat
How to confirm Insert the probe into the center of the thickest part of the food, avoiding bone, as Whirlpool says
- 3
A shorted meat probe (F4 E1)
What separates it The code is F4 E1 and a probe cycle will not run
How to confirm Measure the probe with the range unplugged: the range table gives 59,000 ohms at room temperature; if not, replace the probe
- 4
A worn jack or damaged jack wiring
What separates it The probe reads fine on a meter but the connection is loose in the jack
How to confirm Check that the probe sits firmly in the jack and reconnect any loose jack harness; replace a worn jack
Before you touch a setting
Record this first — changing settings destroys the evidence
- The exact display: Probe, Insert Probe, 3D31, 3D32, 3D41, F3 E4 or F4 E1
- Whether the probe sits firmly in the jack
- Whether the probe was pushed into the food
Try in this order
0 of 7 completedWhat to do first
ReversiblePush the probe fully into its jack and into the food.
Correct only the documented fault domain
ReversibleCheck the probe jack, the harness and the probe's own resistance. Whirlpool documents one check for this code — verify meat probe is fully inserted in the meat probe jack — so confirm that before treating anything else as the cause.
Seat the probe
ReversibleWhirlpool's page says to verify the meat probe is fully inserted in the meat probe jack; the jack location varies by model, so check the manual.
Insert it into the food
ReversibleInsert the temperature probe into the center of the fleshy or thickest part of the food; if the meat has a bone, keep the probe away from it.
Measure the probe
ReversibleFor F4 E1 the range table says to unplug the range and the probe and measure the probe's resistance with a volt/ohm meter; it should be about 59,000 ohms at room temperature (two other repair sources give the same figure). If not, replace the probe.
Check the jack and its wiring
ReversibleIf the probe resistance is okay, insert the probe in the jack and check for a firm connection; replace the jack if it is worn or damaged, reconnect a loose jack harness and replace a damaged harness.
Verify once, then respect the service boundary
ReversibleWhirlpool specifies a 1 minute power interruption for this code, not an arbitrary one.
Model-specific
What is true of this model and not of its siblings
- Displayed as
- Probe, Insert Probe; 3D31, 3D32, 3D41; F3 E4; F4 E1.
- Meter reading
- About 59,000 ohms across the meat probe at room temperature.
- Parts named by the service tables
- Meat probe; meat probe jack; wire harness.
Stop boundary
When this stops being a self-service repair
- !Unplug the range before you measure the probe or touch the jack harness
- !Do not use a probe that is bent, frayed or has a damaged cable; it can short and shut the oven down
Evidence ledger
Sources behind this answer
Where the manufacturer's article stops. The 59,000 ohm reading is the range table's own and is confirmed by two other repair sources.
Exact questions
Common questions
What does Probe, Insert Probe, 3D31, 3D32, 3D41, F3 E4, F4 E1 mean on a Whirlpool range?+
the control is looking for the meat probe and cannot read it
What does Probe or Insert Probe mean?+
Whirlpool says the control is looking for an input from the meat probe; it is not a fault.
Can I use the oven without the probe?+
Yes; cook by time or temperature, and leave the probe out of the jack.