Direct answer
For the LG LDP6810 dishwasher, door latch, supply valve, inlet hose, float and control state should be checked before the inlet valve. First, confirm supply is open and start a normal cycle.
What this covers
- LG LDP6810 dishwasher (LDP6810*)
- LG QuadWash dishwasher; steam, Dynamic Dry and ThinQ equipment varies by model.
- The specific fault this record addresses: will not fill with water
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
The supply shut-off valve under the sink is closed or partly closed
What separates it No fill at all, often after plumbing work or after something was moved under the sink.
How to confirm Trace the small supply line from the dishwasher to its valve under the sink and confirm it is fully open.
- 2
The door is not fully latched
What separates it The cycle appears to start but no water enters and no fault appears immediately.
How to confirm Push the door until it latches positively. See not-starting — an unlatched door prevents filling entirely.
- 3
The float switch is stuck up
What separates it The machine behaves as if the tub is already full and refuses to add water. The float is a small plastic dome in the tub floor.
How to confirm Press the float down and check it moves freely and returns. Debris or a dropped item can hold it up, and the machine reads that as a full tub.
- 4
The inlet screen or supply line is restricted
What separates it Filling is slow rather than absent, sometimes with a fill-timeout fault.
How to confirm Sediment collects in the inlet screen, particularly after plumbing work in the building.
- 5
The inlet valve has failed
What separates it Supply confirmed open, door latched, float free, and still no water.
How to confirm This is the conclusion once the simpler causes are ruled out, and is a service repair.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether the supply valve under the sink is fully open.
- Whether the door latches positively, since an unlatched door stops the fill entirely.
- Whether the float in the tub floor moves freely when pressed and springs back.
- Whether there is no water at all, or slow filling.
Confirm the supply shut-off valve under the sink is fully open
ReversibleTrace the line from the dishwasher rather than guessing which valve it is.
Latch the door firmly and confirm the cycle actually starts
ReversibleAn unlatched door prevents filling and often shows no specific fault.
Press the float in the tub floor and confirm it moves freely
ReversibleA float held up by debris makes the machine believe the tub is already full.
Disconnect power and close the supply before inspecting the inlet screen
ReversibleNever work on an inlet valve under pressure or with power connected.
Confirm one fill reaches the normal level and stops
ReversibleVerifies both the fill and the level control.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- LDP6810*. LG QuadWash dishwasher; steam, Dynamic Dry and ThinQ equipment varies by model.
- Drying — auto-open door (Dynamic/Auto Dry)
- LG uses an auto-open door for drying: the door opens automatically at the end to release steam and let air in (LG's answer to Bosch AutoAir / Samsung AutoRelease). The door opening itself is intentional — do not push it shut during the dry phase. Rinse aid still helps plastics.
- Wash & motor
- QuadWash uses four spray arms for coverage, driven by a belt-less Inverter Direct Drive motor (10-year warranty), so wash-noise/vibration is the motor bearing or a blocked arm, not a belt. A 3rd rack and stainless tub.
- Filter & codes
- A manual filter at the tub floor must be cleaned periodically. LG codes — OE drain (filter/hose), IE fill (water supply), LE motor. Filter and spray-arm clogs cause most poor-cleaning complaints.
- Symptom boundary
- This record covers LG LDP6810 dishwasher when it will not fill with water. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Close the supply valve immediately for an uncontrolled fill or an overflow.
- !Never probe a live inlet valve with power connected.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "Dishwasher: No water – “IE” error code". The dishwasher takes no water in; LG's inlet-error article covering supply valve, inlet hose and filter screen. Probed 2026-08-21: title-verified. What that article does not carry is the model boundary — it is written for a product line, and LDP6810* is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
My LG LDP6810 door opens by itself at the end of the cycle.+
That is LG's auto-open drying — the door opens automatically after the wash to let steam escape and dry air in, improving drying without a lot of heat. It is intentional, so leave it open during the drying phase. Keep rinse aid filled too, since it helps water sheet off plastics that LG's low-heat drying leaves dampest.
The cycle runs but no water ever comes in.+
Check three things in order: the supply shut-off valve under the sink is fully open, the door latched positively, and the float in the tub floor moves freely when pressed. A float stuck up by debris makes the machine think the tub is already full, so it never adds water and often shows no fault at all.
Does this answer apply to every LG model?+
No. It is scoped to LDP6810*. LG QuadWash dishwasher; steam, Dynamic Dry and ThinQ equipment varies by model.
What should I record before troubleshooting not filling or no water?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing not filling, no water. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Close water for uncontrolled fill or leakage; never probe a live valve.
Answer for the exact device and software version shown above.