Direct answer
For the LG LREL6325 electric range, normal cycling, rack/cookware, preheat and measurement method must be controlled before calibration. First, measure an empty standardized bake cycle with an appropriate thermometer.
What this covers
- LG LREL6325 electric range (LREL6325F)
- LG range/oven; gas, electric, induction, ProBake, InstaView and ThinQ equipment vary.
- The specific fault this record addresses: oven temperature is too hot, too cool or uneven
What it does not cover
- ×The same symptom on a different LG product line, which has its own record and its own cited source
- ×An on-screen error code whose meaning has not been checked against this exact model's manual
- ×Live electrical, gas, sealed-system, internal battery-cell or structural repair — a technician boundary, not a self-service step
Differential
What actually causes this, and how to tell them apart
These are ordered by how often each one is the answer, not by how easy it is to try. The point of the middle column is that two causes producing the same headline symptom rarely produce the same detail — that detail is what tells you which one you have before you change anything.
- 1
Normal cycling was misread as instability
What separates it A thermometer reading taken once shows a temperature above or below the setpoint, but the oven is mid-cycle — ovens cycle heat on and off around the setpoint by design and a snapshot reading during the 'off' or 'on' phase looks wrong even when the average is correct.
How to confirm Take multiple readings over a full 10-15 minute period rather than one spot check, and average them against the setpoint.
- 2
The oven wasn't given a full preheat before the reading
What separates it Temperature reads low specifically right after the 'preheated' indicator or tone, especially on ovens that signal preheat complete before fully stabilizing.
How to confirm Wait an additional 5-10 minutes past the preheat signal before taking a reading or placing food.
- 3
Calibration has genuinely drifted
What separates it A consistent, repeatable offset in the same direction across multiple full-cycle averaged readings, not a one-time snapshot.
How to confirm Most ranges have a documented, limited calibration offset adjustment (commonly ±35°F) in the settings menu — this is intended for exactly this correction and does not require service.
- 4
Uneven heating from rack position or convection setting mismatch
What separates it The average temperature is correct but food browns unevenly, or a recipe written for conventional bake behaves differently on convection.
How to confirm Compare center-rack results on Bake versus Convection using the same test, since convection settings often expect a temperature offset the manual documents.
- 5
A genuinely failed temperature sensor or control board
What separates it A large, repeatable error that calibration adjustment cannot correct, or a reading with no relationship to the setpoint at all.
How to confirm This is the conclusion only after calibration adjustment has been tried and confirmed insufficient.
Before you touch a setting
Record this first — changing settings destroys the evidence
Every item below stops existing the moment a reset, re-pair or settings change is made. Written down first, they are what separates the causes above; recovered afterwards, they are guesswork.
- Whether the reading was a single spot-check or an average over a full 10-15 minute cycling period — this alone resolves most 'wrong temperature' reports.
- Whether the reading was taken immediately at the preheat signal or after additional stabilization time.
- The exact thermometer used and whether it's rated accurate for oven temperatures — many kitchen thermometers are not.
Measure an empty, standardized bake cycle with an oven-rated thermometer
ReversibleTake multiple readings over 10-15 minutes rather than one spot check.
Wait past the preheat signal before the first reading
ReversibleSome models signal preheat complete before fully stabilizing.
Adjust only the documented, limited calibration offset if a consistent error is confirmed
ReversibleDo not attempt calibration beyond what the manual documents as the supported range.
Repeat the same test after correction
ReversibleConfirms the adjustment actually fixed the average, not just one reading.
Model-specific
What is true of this model and not of its siblings
Generic advice for the product line fails here. Each item below is a property of this specific model family that changes which of the steps above apply to you.
- Model scope
- LREL6325F. LG range/oven; gas, electric, induction, ProBake, InstaView and ThinQ equipment vary.
- Cooktop — ELECTRIC radiant smoothtop
- A radiant ELECTRIC smoothtop — elements heat any flat pan by contact and stay hot after use (hot-surface indicator). A burner not heating is the element/control, not cookware type.
- Oven — electric
- Electric oven with LG's ProBake convection (a rear element/fan for even baking) and Air Fry on most builds. No-heat is the element or control.
- Self-clean & features
- EasyClean (low-temp steam) and/or high-heat self-clean (door locks, some smoke normal), ThinQ Wi-Fi on smart builds.
- Symptom boundary
- This record covers LG LREL6325 electric range when it oven temperature is too hot, too cool or uneven. A different symptom on the same hardware, or this symptom on a different LG product line, has its own record with its own causes and its own cited source.
Stop boundary
When this stops being a self-service repair
Continuing past any one of these costs more than the repair saves — in safety, in warranty, or in evidence a technician needs.
- !Stop for runaway heat that doesn't cycle off at all, smoke, a gas odor, or a failed safety cutoff — these are not calibration issues.
Evidence ledger
Sources behind this answer
Visible sources support the visible claims. Home Product Support records the publisher, the fact used and the review date; community reports can suggest an issue but do not become a published fact on their own.
Where the manufacturer's article stops. LG publishes this as "Oven Cooking Issues (Under or Over Cooking)". Oven running hot, cool or unevenly, including LG's temperature-calibration path. What that article does not carry is the model boundary — it is written for a product line, and LREL6325F is the scope applied here. Where a control label, terminal, indicator pattern or reset sequence differs on your unit, the manual for that exact model is the authority, not this page and not the article.
Exact questions
Common follow-ups
My LG LREL6325 oven isn't heating evenly.+
LG's ProBake convection heats from a rear element with a fan for even results, so first make sure you are using the convection mode for multi-rack baking and that the rear fan is not blocked. Uneven baking on the standard mode can be normal oven hot spots — rotate pans. If one part never heats, the bake or convection element may be failing. Also confirm you preheated fully; the smoothtop cooktop is separate from oven heating.
My thermometer read 25 degrees off from the setpoint.+
Take several readings across a full 10-15 minute period rather than trusting one spot check — ovens cycle heat on and off around the setpoint by design, so a single reading during the 'off' phase looks wrong even when the average is accurate.
Is there a way to fix a consistent temperature offset myself?+
Most ranges have a documented, limited calibration adjustment (often around ±35°F) in the settings menu specifically for this. Confirm the error is consistent across multiple averaged readings first, then use that adjustment rather than assuming a part has failed.
Does this answer apply to every LG model?+
No. It is scoped to LREL6325F. LG range/oven; gas, electric, induction, ProBake, InstaView and ThinQ equipment vary.
What should I record before troubleshooting temperature wrong or uneven baking?+
Record the complete model identifier, exact message or indicator, software/firmware where visible, the operating stage and what still works.
Why is a factory reset not the first step?+
A reset can erase accounts, networks, maps, schedules or preferences without distinguishing temperature wrong, uneven baking. The ordered checks preserve that evidence.
When should I stop and use qualified service?+
Stop for runaway heat, smoke, gas odor or a failed safety cutoff.
Answer for the exact device and software version shown above.