Expanded exact-code directory
Craftsman 20057933 Model Garage Door Opener Error Codes error codes
Craftsman 20057933 Model Garage Door Opener Error Codes indicators as Sears PartsDirect (parts and repair reference) lists them, each with its meaning and the first safe check.
- door-doesn-t-close-and-safety-sensors-are-misaligned-orListed as safety sensors are misaligned or sensor
- door-won-t-close-and-green-safety-sensors-are-misaligned-orListed as safety sensors are misaligned or obstructed.
Every code
Every Craftsman 20057933 Model Garage Door Opener Error Codes code: what it means and what to do
- door-doesn-t-close-and-safety-sensors-are-misaligned-or
- door-won-t-close-and-green-safety-sensors-are-misaligned-or
- light-flashes-5-times-and-motor-overheated
Craftsman 20057933 Model Garage Door Opener Error Codes code door-doesn-t-close-and-safety-sensors-are-misaligned-or
Listed as safety sensors are misaligned or sensor wires are broken.
Realign the safety reversing sensors so that the red LED on the receiving sensor glows Parts named: safety sensor wires.
Craftsman 20057933 Model Garage Door Opener Error Codes code door-won-t-close-and-green-safety-sensors-are-misaligned-or
Listed as safety sensors are misaligned or obstructed.
Remove the obstruction between the safety sensors or realign the safety reversing sensors so that the red LED on the receiving sensor glows steadily.
Craftsman 20057933 Model Garage Door Opener Error Codes code light-flashes-5-times-and-motor-overheated
Listed as motor overheated.
The motor can overheat if the door is opened and closed several times in a row. Unplug the garage door opener to reset the logic board. Allow the motor to cool for about 15 minutes before restoring power and using the garage door opener. Pull the emergency door release and check the up-and-down travel of the garage door for binding. Repair the garage door if it doesn’t travel smoothly. If it overheats after a single use and the garage door travel is smooth, replace the motor. Parts named: motor, Garage door components.
Craftsman 20057933 opener codes
The 20057933 model opener reports faults through diagnostic LED flashes on the motor unit and the wall console. Count the flashes and match them to the label on the motor unit or the manual. The safety sensors are the first suspect when the door will not close, and the wall control wiring is the next.
Reprogramme the remotes with the learn button after changing batteries, and check that the limits and force settings let the door travel fully without reversing. Springs, cables and brackets should only be adjusted by a trained technician.
This opener uses a diagnostic LED on the motor head, and counting its flashes after you press the button gives the code. If the opener has been in use a long time, the limit settings may have drifted and the door may stop short or reverse at the floor. The manual explains how to reset the limits, and it also warns you to disconnect power before any adjustment. If the door does not close all the way, adjust the down limit slowly, testing after each change.
The 20057933 is an older Craftsman opener model with a diagnostic LED on the motor head. The pattern of flashes after you press the learn or command button names the fault. Because the opener is old, wear is the usual cause: rollers, cables, limit switches and the motor's capacitor. Note the number of flashes carefully, counting each group, since a miscount leads to the wrong table row.
If the opener runs but the door does not move, the trolley may have disconnected from the carriage. Pull the release cord, lift the door by hand and re-engage the trolley by sliding the carriage until it clicks. If the motor hums and does nothing, the starting capacitor may have failed, which a technician can replace. If it moves only a few centimetres and stops, check the limits and the force.
Keep the door and tracks clean and lubricated and check the balance each year. Do not remove the opener's cover while it is plugged in. Replace a worn-out photo-eye cable promptly. If repair parts are hard to find for this model, a modern opener is a sound replacement and often includes better safety features.
How do I read the diagnostic flashes on a Craftsman opener?
Count the flashes of the LED on the motor unit and look up the number in the manual or on the label.
What happens if the limits drift?
The door may stop short or reverse at the floor.