Kenmore 110 model VMAX top-load washer error codes

Kenmore 110 model VMAX top-load washer code F0 E3

Listed as overload.

The size of the load exceeds the washer's capacity. Open the lid and remove some garments. Restart the cycle.

• The load is bigger than the washer's capacity: The display shows F0 E3 and the load fills the basket right to the top. Open the lid and look at how full the basket is
• Heavy items such as blankets or wet towels that weigh more than the basket can turn: The basket looks half full but the items are very heavy. Take out the heaviest items and see whether the code clears
• A load that has absorbed a lot of water and become too heavy: The code appears after a fill in a load of very absorbent fabric. Remove some garments from the basket and restart the cycle

The chart's repair is to take out part of the load. Start with the heaviest, wettest items.

Close the lid and start the cycle again. A smaller load should run through without the code coming back.

Wash bulky items such as blankets and comforters alone so the basket is not overloaded again.

F0 E3 (110 model VMAX top-load table).

None.

None.

Is it the same as an unbalanced load? No. F0 E5 is a load that is out of balance; F0 E3 is a load that is too big.

How do I stop F0 E3 coming back? Fill the basket loosely rather than packing it, wash blankets and comforters on their own, and split a big load into two. The chart gives no weight limit, only that the load exceeds the washer's capacity.

If the code appears with a normal small load, the fault is probably not the load; see the F0 E5 and F7 E7 pages

Stop and unplug the washer if the lid will not open because of a full basket

Kenmore 110 model VMAX top-load washer code F0 E4

Listed as spin limited by water, temperature,.

This code displays when the water temperature is too high during the final spin. Spin speed is limited to 500 rpm when this code appears. Check the water valve functions using the diagnostic test mode. Replace the water valve assembly if the hot water valve sticks open. Parts named: water valve assembly.

• The water temperature is too high during the final spin: F0 E4 appears near the end of the cycle and the spin runs slower than usual. Note the temperature setting and whether the final water is hot
• A hot water valve that sticks open and lets hot water in during the rinse: Hot water is running when the cycle calls for cold. Check the valve functions using the diagnostic test mode
• A water valve assembly that leaks hot water into the tub: The tub is warmer than the selected rinse temperature should allow. Run the diagnostic test and watch which valve opens

This code displays when the water temperature is too high during the final spin, so it is a limit rather than a stop.

The service test mode lets you open each valve on its own and see whether hot water keeps running when it should not.

The chart names the water valve assembly as the only part for F0 E4, once the valve test shows it stuck.

Water valve assembly.

The diagnostic test mode, and a screwdriver or nut driver for the valve.

How do I test the valves? Use the diagnostic test mode to check the water valve functions.

The spin is limited to 500 rpm when this code shows, so the clothes may come out wetter than usual but the washer is otherwise working

Do not keep running hot cycles if you suspect a hot valve is stuck open, because the tub temperature can climb

Kenmore 110 model VMAX top-load washer code F0 E5

Listed as unbalanced load.

Distribute items evenly when loading. Level the washer cabinet. Check for weak suspension springs. With the washer empty, open the lid and push down firmly on the basket. The basket should not bounce up and down more than once when pushed. Replace the suspension springs if defective. Parts named: suspension springs.

• Items that are bunched to one side of the basket: The washer thumps or shakes hard during spin and the display shows F0 E5. Stop the spin, open the lid and redistribute the load evenly
• A washer cabinet that is not level: The cabinet rocks when pushed at the top corner. Level the washer cabinet using the adjustable feet at the corners
• Weak or broken suspension springs: The basket bounces more than once when pushed down firmly with the washer empty. With the washer empty, open the lid and push down firmly on the basket

Mix large and small items together and keep bulky pieces from bunching up to one side of the basket.

Adjust the feet until the cabinet does not rock, and check it again with a level once the feet are locked.

Open the lid and push down firmly on the basket. It should not bounce up and down more than once; replace the suspension springs if it does.

Suspension springs.

A level and a wrench for the leg locknuts.

How do I test the suspension? With the washer empty, open the lid and push down firmly on the basket. It should not bounce more than once.

Can the floor cause it? An unlevel cabinet can, which is why the chart says to level the washer cabinet.

Stop the spin and unplug the washer if the cabinet is walking across the floor

Do not lean on or hold the washer during spin; a heavy imbalance can move it suddenly

Kenmore 110 model VMAX top-load washer code F1 E1

Listed as main electronic control board failure.

Try to reset the control board by unplugging the washer for 5 minutes and then restoring power. If the F1E1 code returns after restoring power, replace the main electronic control board. Parts named: main electronic control board.

• A fault on the main electronic control board that clears when the board resets: The display shows F1 E1 and the washer will not run a normal cycle. Unplug the washer for 5 minutes, restore power and see whether F1 E1 returns
• A board fault that comes straight back after a reset: F1 E1 returns every time power is restored to the washer. The chart replaces the main electronic control board in that case
• A power surge that upset the control electronics: The code followed a storm, an outage or a breaker trip. Note whether other appliances on the circuit were affected

Leave it fully unplugged, not just switched off, so that the control board can reset completely.

If F1 E1 does not return, the fault was a one-off and needs nothing else.

The chart's only part for F1 E1. Match the board to your full model number.

Main electronic control board.

A screwdriver or nut driver and a wrist strap for board handling.

Stop and unplug the washer if there is a burning smell from the control area

The board is a costly part; price it against the age of the washer before ordering

Kenmore 110 model VMAX top-load washer code F1 E2

Listed as main electronic control board failure.

This code signals a failure in the motor control circuit of the main electronic control board. Unplug the washer and check the main electronic control board wiring. Check the drive motor wiring. Open the lid and spin the impeller inside the basket. The impeller should rotate freely. Remove the restriction in the drive system if the impeller doesn't spin freely. If the basket spins freely, replace the main electronic control board. Parts named: main electronic control board.

• Loose wiring on the main electronic control board or the drive motor: The display shows F1 E2 and the motor does not run normally. Unplug the washer and check the board wiring and the drive motor wiring
• A restriction in the drive system that stops the impeller spinning: The impeller does not turn freely when you spin it by hand inside the basket. Open the lid and spin the impeller; it should rotate freely
• A failure in the motor control circuit of the main electronic control board: The basket and impeller turn freely and the wiring is secure. The chart replaces the main electronic control board when the basket spins freely

and look for connectors that have backed out or scorched pins.

Follow the harness to the drive motor and reseat each connector. A loose motor connector gives the same code as a failed board.

It should rotate freely. Remove any restriction in the drive system; if the basket spins freely, replace the main electronic control board.

Main electronic control board.

A screwdriver or nut driver.

What do I check before the board? The board wiring, the drive motor wiring and whether the impeller spins freely.

Unplug the washer before checking any wiring or reaching into the basket

Do not force the impeller; a restriction that will not clear needs a technician to open the drive system

Kenmore 110 model VMAX top-load washer code F1 E3

Listed as mismatch of the main electronic control board and the user interface control.

The code appears when you install the wrong user interface control. Order and install the correct user interface control for your model of washer. Parts named: user interface control.

• The wrong user interface control was installed for this washer: F1 E3 appeared right after the user interface control was replaced. Compare the part number of the fitted control against the one for your model number
• A control from a similar washer with a different software version: The control looks identical but its part number differs from the parts list. Look up your full model number in a parts list and check the number
• A replacement main electronic control board that does not pair with the control: The main board was replaced instead of the user interface control. Check whether the board was the part changed and compare numbers with the parts list

The chart says the code appears when you install the wrong user interface control, so start with the last part you changed.

Use a parts list for your exact model. A visually identical control can carry different software.

Unplug the washer before you open the console. The chart names only the user interface control for F1 E3.

User interface control.

Your model number, a parts list and a screwdriver or nut driver.

Stop refitting parts until the model number matches the part number

Return a control that the seller cannot confirm fits your washer

Kenmore 110 model VMAX top-load washer code F2 E1

Listed as stuck button.

Attempt to release the stuck button. If you cannot release the stuck button, replace the user interface control. Parts named: user interface control.

• A button on the user interface control is stuck down: The display shows F2 E1 and one button feels jammed or does not spring back. Press each button and see whether any stays down
• Moisture or residue holding a button: The console is damp or sticky from spills or steam. Dry and clean the console and try releasing the button again
• A failed user interface control with a shorted button: The button will not release however much you work it. The chart replaces the user interface control if you cannot release the button

Press it a few times and clean around it. The chart's first step is simply to free the button.

A film of moisture can hold a button, so let the console dry and try each button once more.

Unplug the washer first and match the control to your model number. The chart names only this part.

What is the fix? Attempt to release the stuck button; if you cannot, replace the user interface control.

Can I keep using the washer? The code is a fault, so the chart's fix comes first; a stuck button can make the control ignore other input.

Which button is usually the stuck one? The chart does not say. Press each button on the console and see which one stays down or feels sticky, and clean around it, because moisture or residue can hold a key without any part having failed.

Unplug the washer if liquid has run behind the console

Do not pry at the button with a tool, since a broken button means replacing the whole control

Kenmore 110 model VMAX top-load washer code F2 E3

Listed as user interface control or main electronic control board mismatched.

The code appears when you install the wrong user interface control or main electronic control board. Order and install the correct user interface control or main electronic control board for your model of washer. Parts named: user interface control board, main electronic control board.

• The wrong user interface control was installed: F2 E3 appeared right after the user interface control was replaced. Compare its part number against the one for your model number
• The wrong main electronic control board was installed: F2 E3 appeared right after the main electronic control board was replaced. Compare that board's part number against the one for your model number
• The two parts come from different versions of the washer: One part is original and the other is a replacement that does not pair with it. Check the version marks on both parts against the parts list

The code appears when you install the wrong user interface control or main electronic control board, so identify the last one changed.

Use a parts list for your exact model and compare each stamped number on both the control and the board.

Unplug the washer before you open the console or the board cover. The chart names the user interface control board and the main electronic control board.

User interface control board and main electronic control board.

Your model number, a parts list and a screwdriver or nut driver.

Stop refitting parts until the model number matches the part numbers

Return a part that the seller cannot match to your model number

Kenmore 110 model VMAX top-load washer code F2 E4

Listed as user interface control error.

Unplug the washer. Open the console and check the wire harness connection between the main electronic control board and the user interface control. If the wire harness connection is okay, replace the user interface control. Parts named: user Interface control.

• A loose or damaged wire harness between the main electronic control board and the user interface control: F2 E4 appears and the console behaves erratically or goes dark. Unplug the washer, open the console and check the harness connection
• A failed user interface control: The harness connection is good and the code remains. The chart replaces the user interface control after the harness check
• Moisture inside the console: The console was wet or the washer stood in a damp spot. Look inside the console for damp or corroded contacts

Follow the service instructions for your model; the console usually lifts off after a few screws.

Reseat the connectors at both ends and look for a wire that is pinched or burnt.

The chart names only the user interface control for F2 E4. Match it to your model number.

Do I need to replace the control if the console is dark? Not straight away. The chart checks the wire harness between the main electronic control board and the user interface control first, and replaces the control only if the connection is okay.

Unplug the washer before you open the console panel

If there is corrosion or liquid inside, dry it and check for damage before you power the washer again

Kenmore 110 model VMAX top-load washer code F2 E5

Listed as user interface failure.

Unplug the washer and replace the user interface control. Parts named: user interface control.

• The user interface control has failed: The display shows F2 E5 and the console does not respond or is dark. The chart replaces the user interface control after unplugging the washer
• A power surge that damaged the control: The code followed a storm, an outage or a breaker trip. Note whether other appliances on the circuit were affected
• Moisture or corrosion inside the console: The console was wet or the display is spotted. Look inside the console for damp or corroded contacts

Use the plug rather than the controls, and leave it out while you work in the console.

F2 E4 checks the harness first; F2 E5 goes straight to the control, so a harness check is optional.

The chart names only the user interface control. Order it by your full model number so the software matches the board.

Is there a check before the replacement? The chart says to unplug the washer and replace the user interface control.

Is there any test before replacing the control? The chart gives none for F2 E5; it unplugs the washer and replaces the user interface control. Confirm the code is F2 E5 and not F2 E4, which checks the harness first, before you order the part.

Will a new control need setting up? The chart says only to unplug the washer and replace the user interface control. Order the part by your full model number, because the control must match the main electronic control board, as the F1 E3 and F2 E3 pages explain.

Unplug the washer before you open the console panel

Price the control against the age of the washer before ordering, since it is one of the costlier parts

Kenmore 110 model VMAX top-load washer code F3 E1

Listed as water level signal out of range.

Check the water level pressure tube for kinks, blockages or air leaks.

Replace the water level pressure tube if damaged. The water level detector is a component of the main electronic control board. If the water level pressure tube is okay, replace the main electronic control board. Parts named: water level pressure tube, main electronic control board.

• A kinked, blocked or leaking water level pressure tube: The water level reads wrong and the display shows F3 E1. Check the pressure tube for kinks, blockages or air leaks
• A pressure tube that has split or come off its fitting: The tube looks damaged or loose at either end. Replace the water level pressure tube if it is damaged
• A water level detector fault on the main electronic control board: The tube is sound and the code still remains after checking it. The chart says the detector is a component of the board, so replace the board if the tube is okay

Follow the tube from the tub to the control. Blow gently through it if it is off, to check it is clear.

The tube is a cheap part and gives the same code as a failed board.

The chart says the water level detector is a component of the main electronic control board.

Water level pressure tube and main electronic control board.

Where is the water level detector? It is a component of the main electronic control board, per the chart.

Can I test the pressure tube? Yes, by eye and by breath. Look for kinks, splits and water in the tube, and with it off, blow gently through it to check it is clear. The chart replaces the tube if it is damaged, and the board only if the tube is okay.

Unplug the washer before working near the tube and the board

The board is a costly part; check the tube carefully first

Kenmore 110 model VMAX top-load washer code F3 E2

Listed as water temperature sensor failure.

The water temperature sensor is a component on the water valve assembly. Unplug the washer and check the wire harness connection between the main electronic control board and the water valve assembly. If the wiring is okay, replace the water valve assembly. Parts named: water valve assembly.

• A loose or damaged wire harness between the main electronic control board and the water valve assembly: F3 E2 appears and the washer cannot control water temperature. Unplug the washer and check the harness connection
• A failed water temperature sensor, which is a component on the water valve assembly: The wiring is good and the sensor gives no reading. The chart replaces the water valve assembly because the sensor is part of it
• A damaged harness that gives an open or shorted reading: The connector is seated but a wire is worn. Replace the wire harness if it is damaged or corroded

Reseat the connectors at both ends of the harness and reconnect any loose wires you find along it.

The chart repairs the wiring before it replaces the valve assembly, since a worn wire gives the same code and costs far less.

The chart says the water temperature sensor is a component on the water valve assembly, so the whole assembly is replaced.

Where is the sensor? The chart says it is a component on the water valve assembly.

Do I replace the sensor alone? No. It is part of the water valve assembly.

Unplug the washer before reaching the valve or the harness

The sensor is not sold on its own here, so expect to replace the whole valve assembly

Kenmore 110 model VMAX top-load washer code F5 E1

Listed as lid switch error.

This code displays when the lid switch detects an open lid with the lid locked. Unplug the washer and check the wire harness connections on the lid lock/switch. If the wiring connections are okay, replace the lid lock/switch. Parts named: lid lock/switch.

• The lid switch detects an open lid while the lid is locked: F5 E1 appears during a cycle and the lid looks closed. Check that the lid closes fully and nothing holds it slightly open
• A loose or damaged wire harness on the lid lock/switch: The connector at the lid lock/switch is loose or the wire is worn. Unplug the washer and check the wire harness connections on the lid lock/switch
• A failed lid lock/switch: The wiring connections are good and the code remains. The chart replaces the lid lock/switch after the wiring check

A folded garment or a bent hinge can leave the lid slightly ajar. The code appears when the switch reads an open lid while the lid is locked.

Reseat each connector at the lid lock and the board, and look for a wire that is pinched or burnt.

The chart names the lid lock/switch as the only part for F5 E1, so the board and the harness are left alone.

Lid lock/switch.

Do not bypass the lid switch to run the washer, because the basket spins fast enough to cause injury with the lid open

Unplug the washer before touching the lid lock/switch wiring

Kenmore 110 model VMAX top-load washer code F5 E2

Listed as lid won't lock.

Check for debris in the lid lock mechanism that could prevent it from locking.

Unplug the washer and check the wire harness connections for the lid lock/switch on the main electronic control board. Examine the lid lock/switch assembly. If it's damaged or defective, replace it. Parts named: lid lock/switch.

• Debris in the lid lock mechanism that stops it locking: F5 E2 appears at the start of a cycle and the lid does not latch. Look into the lock mechanism for lint, coins or a broken piece
• A loose or damaged wire harness for the lid lock/switch on the main electronic control board: The connector at the control board is loose or has backed out. Unplug the washer and check the harness connections at the board
• A damaged or defective lid lock/switch assembly: The mechanism is clear, the wiring is good and the lid still does not lock. Examine the lid lock/switch assembly and replace it if it is damaged

Look for lint, a coin or a broken piece that stops the lock from moving fully.

Reseat the connector on the board and check the wire runs to the lid lock.

The chart names only the lid lock/switch as the part for F5 E2, and replaces it if it is damaged or defective.

A screwdriver or nut driver and a flashlight.

Do not run the washer with a lid that will not lock, because the basket can spin with the lid unlatched

Unplug the washer before checking the lock wiring at the board

Kenmore 110 model VMAX top-load washer code F5 E3

Listed as lid won't unlock.

Unplug the washer. Check the wire harness connections for the lid lock/switch assembly on the main electronic control board. If the connections are okay, then you will typically need to force the lid open. This will usually break the lid lock/switch. Replace the lid lock/switch if it's damaged or broken. Parts named: lid lock/switch.

• A loose or damaged wire harness for the lid lock/switch on the main electronic control board: F5 E3 appears after a cycle and the lid stays locked. Unplug the washer and check the harness connections at the board
• A lid lock/switch that is stuck in the locked position: The wiring is good and the lid still will not open. The chart says you will typically need to force the lid open
• A lid lock/switch broken by forcing the lid: The lid was forced and the lock is now damaged. Replace the lid lock/switch if it is damaged or broken

Make sure the basket has stopped turning and the water is drained before you go on.

Reseat the connector on the board and check the whole wire run up to the lid lock.

The chart says you will typically need to force the lid open, which will usually break the lid lock/switch.

A screwdriver or nut driver and a flat tool to release the lid.

Make sure the basket has stopped and the tub is drained before you force the lid, because water and a moving basket are hazards

Unplug the washer and let the basket stop before forcing anything

Kenmore 110 model VMAX top-load washer code F5 E4

Listed as lid not opened, between loads,.

The main electronic control board doesn't detect the lid opening between loads. Unplug the washer and check the wiring connections between the lid lock/switch and the main electronic control board. If the wiring connections are okay, replace the lid lock/switch. Parts named: lid lock/switch.

• The lid was not opened between loads, so the control never saw it open: F5 E4 appears at the start of the next load and the lid was left closed. Open and close the lid between loads and start the cycle
• A loose or damaged wiring connection between the lid lock/switch and the main electronic control board: The lid opens and closes but the control never registers it. Unplug the washer and check the wiring connections
• A lid lock/switch that does not register the lid opening: The wiring is okay and the code still remains afterwards. The chart replaces the lid lock/switch if the wiring is okay

The main electronic control board expects the lid to open between loads, and F5 E4 means it did not detect that.

Reseat every connector between the lid lock and the board, and look for a worn or pinched wire.

The chart names the lid lock/switch as the part for F5 E4, so nothing else is replaced first.

Is it a real fault? Not always. Opening the lid between loads may clear it.

Unplug the washer before touching the lid lock wiring

Do not bypass the lid switch to force a cycle to start

Kenmore 110 model VMAX top-load washer code F6 E2 or F6 E3

Listed as communication error.

This code signals a communication failure between the user interface control and the main electronic control board. Unplug the washer and check the wire harness between the user interface control and the main electronic control board. Replace the user interface control. If the problem persists, replace the main electronic control board. Parts named: user interface, main electronic control board,, wire harness,.

• A loose or damaged wire harness between the user interface control and the main electronic control board: F6 E2 or F6 E3 appears and the console goes dark or ignores the keys. Unplug the washer and check the harness between the control and the board
• A failed user interface control that stops answering the board: The harness is good and the console still does not communicate. The chart replaces the user interface control after the harness
• A failed main electronic control board: A new user interface control still gives the same code. The chart replaces the main electronic control board if the problem persists

at both ends. The harness carries the messages between the two controls.

A worn harness gives the same code as a failed control and costs far less.

The chart's order after the harness is the user interface control first and the main electronic control board second.

F6 E2 or F6 E3 (110 model VMAX top-load table).

User interface control, main electronic control board and wire harness.

Which part is replaced first after the harness? The user interface control.

Unplug the washer before opening the console or the board cover

Replace one part at a time and test between them, since both are costly

Kenmore 110 model VMAX top-load washer code F7 E0

Listed as loss of electrical power.

Plug in the power cord securely. Replace the power cord if damaged. Unplug the washer and check the power cord wiring connections on the main electronic control board. Have an electrician check voltage at the electrical outlet. Parts named: power cord.

• The power cord is not plugged in securely: F7 E0 appears and the washer loses power intermittently. Push the plug fully into the outlet and see whether the code returns
• A damaged power cord: The cord or plug is cracked, burnt or loose at the plug. Inspect the cord and replace it if it is damaged
• Loose power cord wiring connections on the main electronic control board: The cord is sound but the connections at the board have backed out. Unplug the washer and check the cord connections on the board
• A problem with the voltage at the electrical outlet: The outlet is loose, worn or the circuit drops out under load. Have an electrician check the voltage at the electrical outlet

Push the plug fully home and check the outlet holds it. A plug that has worked loose is the cheapest cause.

Inspect the whole cord and both ends. Do not use a cord with a cracked jacket or a burnt plug.

, and have an electrician check the voltage at the electrical outlet if the code returns.

Power cord.

A screwdriver or nut driver; an electrician's voltmeter for the outlet.

Is the washer broken? Often not. The chart's checks are the plug, the cord, the connections at the board and the outlet voltage.

Stop and unplug the washer if the plug or outlet is hot, discolored or smells of burning

The chart says to have an electrician check the voltage at the outlet, so do not test mains voltage yourself unless you are qualified

Kenmore 110 model VMAX top-load washer code F7 E1

Listed as loss of power during, spin mode,.

This fault code displays when power is lost during the spin mode. The washer pauses for 5 minutes to allow the spin basket to stop before continuing the cycle. Plug in the power cord securely. Replace the power cord if damaged. Unplug the washer and check the power cord wiring connections on the main electronic control board. Have an electrician check voltage at the electrical outlet. Parts named: power cord.

• Power was lost while the washer was in spin mode: F7 E1 appears after the lights flickered or a breaker tripped during the spin. Note whether the power dipped or the breaker tripped at the time
• A power cord that is not seated or is damaged: The cord wiggles in the outlet or shows damage. Plug the cord in securely and replace it if it is damaged
• Loose power cord connections on the main electronic control board: The cord is fine but the connection at the board is loose. Unplug the washer and check the cord wiring connections on the board
• A weak or unreliable electrical outlet: The code repeats in spin, when the motor draws the most current. Have an electrician check the voltage at the electrical outlet

The chart says the washer pauses for 5 minutes to allow the spin basket to stop before continuing the cycle. Do not open the lid during that time.

Push the plug fully in and inspect the whole cord and the plug for damage or heat marks.

, and have an electrician check the voltage at the electrical outlet if F7 E1 repeats.

Power cord.

A screwdriver or nut driver; an electrician's voltmeter for the outlet.

Why does the washer pause? The chart says it pauses for 5 minutes to allow the spin basket to stop before continuing the cycle.

Do not open the lid to hurry the pause along, because the basket may still be turning

Stop and unplug the washer if the plug or outlet is hot or discolored

Kenmore 110 model VMAX top-load washer code F7 E2

Listed as drive motor failure.

Unplug the washer and check the wire harness connections between the drive motor and the main electronic control board. Open the lid and spin the impeller inside the basket. The impeller should rotate freely. Remove the restriction in the drive system if the impeller doesn't spin freely. If the basket spins freely, replace the drive motor. If the problem persists, replace the main electronic control board. Parts named: drive motor, wire harness, main electronic control board.

• A loose or damaged wire harness between the drive motor and the main electronic control board: F7 E2 appears and the basket does not turn or hums. Unplug the washer and check the harness connections between the motor and the board
• A restriction in the drive system that stops the impeller spinning: The impeller does not rotate freely when you spin it by hand in the basket. Open the lid and spin the impeller; it should turn freely
• A failed drive motor: The basket and impeller spin freely and the wiring is good. The chart replaces the drive motor when the basket spins freely
• A failed main electronic control board: A new drive motor still gives the F7 E2 code. The chart replaces the board if the problem persists

at the motor and the board, and replace the wire harness if it is damaged.

It should rotate freely. Remove the restriction in the drive system if it does not.

This is the chart's order once the harness and the drive system have both passed their checks.

Drive motor, wire harness and main electronic control board.

How do I test the drive system? Open the lid and spin the impeller inside the basket; it should rotate freely.

Unplug the washer before checking the wiring or reaching into the basket

The drive motor and the board are both costly, so check the harness and the impeller first

Kenmore 110 model VMAX top-load washer code F7 E3

Listed as the clutch engaged the spin basket during the wash cycle.

The clutch should only engage the spin basket during the spin cycle. Unplug the washer and check the clutch for obstructions. Remove any obstructions and replace the clutch if damaged. Parts named: clutch.

• An obstruction in the clutch that makes it engage at the wrong time: F7 E3 appears during the wash and the basket turns when only the agitator should move. Unplug the washer and check the clutch for obstructions
• A damaged clutch that engages the spin basket during the wash: The clutch shows wear, breakage or a stuck part. Remove any obstructions and replace the clutch if it is damaged
• A clutch that has failed in the engaged position: The basket turns with the agitator on every wash cycle. Compare basket movement with what the wash cycle should do

The clutch should only engage the spin basket during the spin cycle, so anything that jams it partly engaged causes F7 E3.

Take out debris or foreign objects and check that the clutch moves freely by hand with the washer unplugged.

The chart names the clutch as the only part for F7 E3, so the board and the motor are left in place.

Clutch.

A screwdriver, socket set and a helper to tilt the washer.

When should the clutch engage? Only during the spin cycle, according to the chart.

Unplug the washer before working on the clutch, which sits under the tub

The clutch is a heavy, awkward part; consider a technician if you have not opened this drive before

Kenmore 110 model VMAX top-load washer code F7 E4 and F7 E5

Listed as clutch failure.

The clutch failed to engage the spin basket in the spin mode. Unplug the washer and check the clutch for obstructions. Remove any obstructions. Replace the clutch if damaged. Check the wiring connections between the clutch and the main electronic control board. If the wiring connections are okay, replace the clutch. Parts named: clutch, wire harness.

• An obstruction that stops the clutch engaging the spin basket: F7 E4 or F7 E5 appears at spin and the basket does not spin up. Unplug the washer and check the clutch for obstructions
• A damaged clutch that fails to engage: The clutch shows wear, breakage or a slipping part. Remove any obstructions and replace the clutch if it is damaged
• Loose or damaged wiring between the clutch and the main electronic control board: The clutch is fine mechanically but never gets its signal. Check the wiring connections and replace the wire harness if damaged

The chart says the clutch failed to engage the spin basket in spin mode, so start by looking for anything that blocks it.

A worn clutch slips and cannot turn the basket, so replace it if it is damaged after clearing anything that blocks it.

and replace the wire harness if damaged. If the wiring is okay, replace the clutch.

F7 E4 and F7 E5 (110 model VMAX top-load table).

Clutch and wire harness.

A screwdriver, socket set and a helper to tilt the washer.

Unplug the washer before working on the clutch or its harness

The clutch is heavy and awkward; consider a technician if you have not opened this drive before

Kenmore 110 model VMAX top-load washer code F7 E6

Listed as drive motor circuit failure.

Unplug the washer and check the wire harness connections between the drive motor and the main electronic control board. If the wire harness is okay, replace the drive motor. Parts named: drive motor, wire harness.

• A loose or damaged wire harness between the drive motor and the main electronic control board: F7 E6 appears and the drive circuit reports a fault. Unplug the washer and check the harness connections at the motor and at the board
• A failed drive motor whose circuit is open or shorted: The harness is good and the F7 E6 code returns on the next cycle. The chart replaces the drive motor after the wire harness passes
• A wire harness that reads open along its length: The connectors are seated but the wire inside is broken. Replace the wire harness if it is damaged

at the motor plug and at the board, and check that the connectors are pushed fully home.

A damaged harness gives the same drive circuit fault as a failed motor and costs far less.

The chart names the drive motor and the wire harness as the parts for F7 E6.

Drive motor and wire harness.

Unplug the washer before checking the wiring at the motor

The chart does not test the board for this code, so if a new motor does not fix it, have a technician look

Kenmore 110 model VMAX top-load washer code F7 E7

Listed as motor not able to reach target rpm.

Mechanical friction in the drive system caused by items stuck between the spin basket and tub prevents the motor from reaching the target rpm. Remove any obstructions between the spin basket and tub. An unbalanced load can also cause the F7E7 error code. Distribute items evenly when loading. Level the washer cabinet. Check for weak suspension springs. With the washer empty, open the lid and push down firmly on the basket. The basket should not bounce up and down more than once when pushed. Replace the suspension springs if defective. Unplug the washer and check the wire harness connections between the drive motor and the main electronic control board. If the wire harness is okay, replace the drive motor. Parts named: drive motor, suspension springs.

• Items stuck between the spin basket and the tub causing friction: F7 E7 appears in spin and the basket is slow or noisy. Remove any obstructions between the spin basket and the tub
• An unbalanced load: The load is bunched to one side and the washer shakes. Distribute items evenly when loading and level the washer cabinet
• Weak suspension springs: The empty basket bounces more than once when pushed down firmly. With the washer empty, open the lid and push down firmly on the basket
• Loose or damaged drive motor wiring: The motor cannot draw full power through a worn harness. Unplug the washer and check the harness between the drive motor and the board
• A failed drive motor: The wire harness is okay and the motor still cannot reach speed. The chart replaces the drive motor if the wire harness is okay

Mechanical friction from stuck items keeps the motor from reaching the target rpm. Look carefully with a flashlight.

An unbalanced load can also cause F7 E7. With the washer empty, push down firmly on the basket; it should not bounce more than once. Replace the springs if it does.

and replace a damaged harness; if the harness is okay, replace the drive motor.

Drive motor and suspension springs.

A flashlight, a level, and a screwdriver or nut driver.

Unplug the washer before reaching between the basket and the tub or checking the wiring

Do not keep running spin cycles with a heavy imbalance, because the cabinet can move and the parts wear fast

Kenmore 110 model VMAX top-load washer code F7 E8

Listed as overheated motor.

Mechanical friction in the drive system caused by items stuck between the spin basket and tub can overheat the motor. Remove any obstructions between the spin basket and tub. The water level and load size detection systems may need calibrating if water level is too low for the selected cycle. Run the Service Calibration in the Service Test Mode to calibrate water level to washer cycles. A defective drive motor will overheat. Replace the drive motor if defective. Parts named: drive motor.

• Items stuck between the spin basket and the tub causing friction that overheats the motor: F7 E8 appears after a long or heavy load and the motor housing is hot. Remove any obstructions between the spin basket and the tub
• Water level too low for the selected cycle so the motor works harder than it should: The tub level looks low for the load size. Run the Service Calibration in the Service Test Mode to calibrate water level to the cycles
• A defective drive motor that overheats on its own: The obstructions are cleared, the level is calibrated and the motor still runs hot. The chart replaces the drive motor if it is defective

Mechanical friction from stuck items can overheat the motor. Remove any obstructions you find, using a flashlight to see the gap.

The chart says the water level and load size detection systems may need calibrating if the water level is too low for the selected cycle. Run the Service Calibration.

The chart says a defective drive motor will overheat, and names the drive motor as the only part for F7 E8.

Drive motor.

A flashlight and a screwdriver or nut driver; the Service Test Mode for calibration.

What can overheat the motor? Friction from items stuck between the basket and tub, a water level too low for the cycle, or a defective motor.

How do I calibrate the water level? Run the Service Calibration in the Service Test Mode, per the chart.

Let the motor cool with the washer unplugged before you touch it

Do not keep running cycles with an overheating motor, because the winding can be damaged

Kenmore 110 model VMAX top-load washer code F7 E9

Listed as locked rotor.

The motor doesn't move when activated. Check for mechanical friction in the drive system caused by items stuck between the spin basket and tub. Remove any obstructions between the basket and tub. If there are no obstructions, replace the drive motor. Parts named: drive motor.

• Items stuck between the spin basket and the tub that stop the basket moving: F7 E9 appears and the motor does not move at all when activated. Check for stuck items between the basket and the tub
• A seized drive motor: There are no obstructions and the motor still does not move. The chart replaces the drive motor if there are no obstructions
• A jammed drive system: The impeller does not turn freely by hand inside the basket. Open the lid and try turning the impeller by hand

The chart says this is the first cause of a motor that does not move when activated.

Use a flashlight and take out anything wedged there, such as a coin, a bra wire or a small item of clothing.

The chart names the drive motor as the only part for F7 E9, and replaces it only after the obstruction check has passed.

Drive motor.

A flashlight and a screwdriver or nut driver.

Unplug the washer before reaching between the basket and the tub

A motor that hums but does not turn can overheat, so do not keep restarting the cycle

Kenmore 110 model VMAX top-load washer code F8 E3

Listed as overflow or flood condition.

The electronic control senses a water level that exceeds washer capacity. Check the water level pressure tube for kinks, blockages or air leaks. Replace the water level pressure tube if damaged. Check to see if water siphons out through the drain hose. Install the washer drain system according to installation manual guidelines to prevent siphoning of fill water. A leaking water valve can cause the F8E3 code. Unplug the washer and see if the tub fills with water. If so, replace the water valve assembly. Parts named: water level pressure tube, water valve assembly.

• A kinked, blocked or leaking water level pressure tube: F8 E3 appears when the tub is not actually overfull and the level reads too high. Check the pressure tube for kinks, blockages or air leaks
• Fill water siphoning out through the drain hose: The drain hose is fitted too far down the standpipe or has no air break. Install the drain system according to the installation manual to prevent siphoning
• A leaking water valve that fills the tub even when the washer is off: The tub gains water after the cycle ends or with the washer unplugged. Unplug the washer and see whether the tub fills with water

Replace the water level pressure tube if it is damaged, since a bad tube can make the control read a level that is not real.

Install the washer drain system according to the installation manual guidelines to prevent siphoning of fill water.

A leaking water valve can cause F8 E3. If the tub fills with the washer unplugged, replace the water valve assembly.

Water level pressure tube and water valve assembly.

Towels, a bucket and a screwdriver or nut driver.

Can a bad tube cause it? Yes. A kinked, blocked or leaking pressure tube can make the control read the wrong level.

Can the water valve cause it? Yes. A leaking valve can fill the tub, so the chart tests by unplugging the washer.

Shut off both water supply valves at once if the tub keeps filling with the washer unplugged, because a stuck valve can flood the room

Unplug the washer before checking the tube or valve

Kenmore 110 model VMAX top-load washer code F8 E6

Listed as water hazard.

This fault code displays when the main electronic control board senses water in the tub with the lid open for more than 10 minutes. A leaking water inlet valve fills the tub when the washer is off. Replace the water inlet valve if leaking. Parts named: water inlet valve.

• A leaking water inlet valve that fills the tub while the washer is off: F8 E6 appears after the washer has stood idle with the lid open and water is in the tub. Check the tub for water when the washer has not been run
• The lid was left open for more than 10 minutes with water in the tub: Water is in the tub and the lid has stood open for a long time. Note how long the lid has been open with water in the tub
• Water left in the tub by a drain fault: The tub did not empty after the last cycle. Check whether the washer drained fully before the code appeared

The chart says the code displays when the main electronic control board senses water in the tub with the lid open for more than 10 minutes.

A leaking water inlet valve fills the tub when the washer is off, so watch the level with the supply valves closed and then open.

The chart names the water inlet valve as the only part for F8 E6, and replaces it if it is leaking.

Water inlet valve.

Towels, a bucket and a screwdriver or nut driver.

Shut off both water supply valves if the tub is gaining water while the washer is idle

Unplug the washer before working near the inlet valve

Kenmore 110 model VMAX top-load washer code F9 E1, F9 E2, drn or dr

Listed as long drain time.

This code is displayed when the water level does not change after the drain pump runs. If the washer does not drain, check the drain hose and washer drain for a clog or restriction. Unplug the washer and check the drain pump for a clog. If the drain pump is defective, replace it. If the washer is draining correctly and the drop in water level isn't being detected, replace the main electronic control board. Parts named: drain pump, main electronic control board.

• A clogged or restricted drain hose or washer drain: The tub does not empty and the display shows F9 E1, F9 E2, drn or dr. Check the drain hose and the washer drain for a clog or restriction
• A clogged drain pump: The hose and drain are clear but water stays in the tub. Unplug the washer and check the drain pump for a clog
• A defective drain pump: The pump is clear and the wiring is fine but it will not move water. The chart replaces the drain pump if it is defective
• The water level drop is not being detected even though the washer drains correctly: The tub empties normally and the code still appears. The chart replaces the main electronic control board if the drain is fine

The chart displays these codes when the water level does not change after the drain pump runs, so start with the drain path.

Look for lint, a coin or a sock. Replace the drain pump if it is defective.

The chart says a washer that is draining properly but does not register the level change points to the board.

F9 E1, F9 E2, drn or dr (110 model VMAX top-load table).

Drain pump and main electronic control board.

A shallow pan, towels and a screwdriver or nut driver.

What do F9 E1, F9 E2, drn and dr mean? A long drain time: the water level does not change after the drain pump runs, in the chart's words.

Are all four codes the same fault? The chart lists them on one row with the same steps.

What if the tub drains but the code still shows? The chart replaces the main electronic control board, because the level drop is not being detected.

Unplug the washer and bail out the tub before reaching to the drain pump, since standing water hides live wiring

Do not keep running cycles with a tub that will not empty

Kenmore 110 model VMAX top-load washer code LF or F8 E1

Listed as long fill.

Make sure that both water supply valves behind the washer are fully open.

In winter, check the fill lines for freezing. Check the drain system for a siphon problem. If the water valve assembly is defective, replace it. Parts named: water valve assembly.

• One or both of the water supply valves behind the washer are not fully open: The tub fills very slowly or stops short and the display shows LF or F8 E1. Pull the washer forward a little and check that both valves are fully open
• Frozen fill lines in cold weather: The code appears only in winter and the hoses or the wall pipes are very cold to the touch. Check the fill lines for ice and let them thaw before you run another load
• A siphon problem in the drain system that lets the fill water run straight out: The tub fills, then the level drops while water is still coming in. Check the drain hose installation and how far it sits inside the standpipe
• A defective water valve assembly: Water supply and drain are good and the tub still fills too slowly. The chart replaces the water valve assembly after the supply and drain checks

Pull the washer forward a little so you can see and reach both faucets, and keep towels ready for drips at the hose connections.

A frozen line lets only a trickle through, so the fill runs past its time limit. Thaw the lines before running another load.

Make sure the drain hose is installed as the manual shows so fill water cannot run out through it; the valve assembly is the last part the chart replaces.

LF or F8 E1 (110 model VMAX top-load table).

Towels and a bucket for hose water, and a screwdriver or nut driver if you go on to the valve.

What do LF and F8 E1 mean on a Kenmore 110 VMAX washer? A long fill: the tub took too long to fill, in the chart's words.

Can cold weather cause it? Yes. The chart says to check the fill lines for freezing in winter.

Can the drain cause a fill fault? Yes. A siphon in the drain system lets fill water run out while the tub is filling.

Stop and shut the faucets if a hose connection leaks or the tub fills past its normal level

If the house supply flow is weak at other taps, the fault is in the plumbing rather than the washer, so have a plumber look

Kenmore 110 model VMAX top-load washer code Sd or F0 E2

Listed as excessive suds.

If you see excessive suds in the washer, start using the right amount of high-efficiency (HE) detergent. Parts named: (HE) detergent.

• Regular detergent, or too much detergent, used in a high-efficiency washer: Foam rises in the tub or fills the cabinet and the display shows Sd or F0 E2. Look for foam in the tub and check which detergent and how much was used
• A detergent that is not labeled HE for this washer: The detergent box has no HE mark and suds are heavy on every load. Read the detergent label for the HE symbol and switch to an HE detergent
• Detergent residue from earlier loads that keeps making suds: The suds appear even with a small dose of HE detergent. Run an empty rinse cycle and see whether the foam returns

Open the lid once the washer has paused. Heavy foam that fills the tub or spills is the sign the control is reacting to.

The chart's whole repair: use HE detergent in the dose on its label. Regular detergent makes far more suds than this washer's control expects.

Let the washer run through and check the tub is clear before the next load.

Sd or F0 E2 (110 model VMAX top-load table).

HE detergent; no part.

Towels and a measuring cup for the detergent dose.

What do Sd and F0 E2 mean? Excessive suds, in the chart's words.

Does adding more detergent help? No. More detergent makes more suds.

Stop the cycle and unplug the washer if suds have overflowed the lid or dripped into the console

Do not add more detergent to fight suds, because that only makes them worse

Kenmore 110 model VMAX top-load washer code dE

Listed as lid not closed.

If the lid is closed and this message appears when you start the cycle, unplug the washer and check the wire harness connection on the lid lock/switch assembly. If the wiring connections are sound, the lid lock/switch assembly usually needs to be replaced. Parts named: lid lock/switch assembly.

Kenmore 110 model VMAX top-load washer code dL

Listed as lid lock failure.

Check for debris in the lid lock assembly that could prevent the lock mechanism from engaging.

Unplug the washer and check the wiring connections on the lid lock/switch assembly. If you find no wiring problems, you usually need to replace the door lock/switch assembly. Parts named: lid lock/switch assembly.

Kenmore 110 model VMAX top-load washer code E6

Listed as clutch error.

The control detects a problem with the clutch motor. Unplug the washer. Check the wiring harness connections between the main electronic control board and the clutch motor. If the wiring connections are sound, the clutch motor or the main electronic control board usually needs to be replaced. Parts named: clutch motor, Main electronic control board.

Kenmore 110 model VMAX top-load washer code FE

Listed as water level too high.

The washer is usually fills continuously because a water valve failed when this code appears. Unplug the washer and shut off the water supply. The water inlet valve assembly usually needs to be replaced to fix this problem. Parts named: water inlet valve assembly.

Kenmore 110 model VMAX top-load washer code IE

Listed as washer fills slowly.

Check the water supply faucets behind the washer to make , sure that they are fully open.

Check the fill hoses for kinks or freezing (in winter). Check the screens on the water inlet valves for debris or deposits. Replace the water inlet valve assembly if the water inlet screens are clogged., Parts named: water inlet valve assembly.

Kenmore 110 model VMAX top-load washer code LE

Listed as drive motor thermal overload tripped.

A failed drive motor or a restriction in the drive system of the washer causes this code. Unplug the washer. See if the basket spins freely. If not, examine and repair the cause of the restriction in the drive system. If the basket spins freely, check the wiring connections between the drive motor and the control board. Check the resistance through the drive motor windings. The winding should measure between 5 and 15 ohms. If the motor is defective, replace it. Parts named: drive motor, Drive system components.

Kenmore 110 model VMAX top-load washer code PE

Listed as water level sensor failure.

Unplug the washer and check the wire harness connections between the water level sensor and the electronic control board. or replace the wire harness if damaged. If the wire connections are okay, replace the water level sensor. Parts named: water level sensor, wire harness.

Kenmore 110 model VMAX top-load washer code tE

Listed as thermistor error.

Unplug the washer and check the wiring between the control board and the thermistor (temperature sensor). If the wiring is sound, measure the resistance of the thermistor. It should read between 80,000 to 90,000 ohms) at room temperature. If the thermistor is defective, replace it. If resistance of the thermistor is normal through the circuit, replace the main electronic control board. Parts named: thermistor, Main electronic control board.

Kenmore 110 model VMAX top-load washer code uE

Listed as load is out of balance or too small.

If a small load is in the washer, add a few towels or garments to the load. If the load is a normal size, then redistribute the load and see if the washer spins. If the washer tub moves and bangs violently during the spin cycle, one or more of the suspension rod/spring assemblies may need to be replaced. Unplug the washer and examine those components. Parts named: suspension rod/spring assembly.

Kenmore 110 model VMAX top-load washer code CA or CI

Listed as drive motor locked up.

Overloading the washer can prevent the drive motor from spinning. Fill the basket loosely with clothes but don't pack the garments down or continue to add clothes once the basket is full. Remove some clothes if you overfilled the washer. If you didn't overfill the washer, then the washer could have a defective drive motor or failed u-joint. Parts named: drive motor, U-joint.

Kenmore 110 model VMAX top-load washer code CE

Listed as communications error between the main electronic control board and the motor control board.

Unplug the washer and check the wire harness connections between the main electronic control board and the motor control board. or replace the wire harness if damaged. Check the wire harness connections between the motor control board and the drive motor. Also check the wire harness connections between the drain pump and the motor control board because the motor control board also powers the drain pump. or replace any wire harness that's damaged. If the wire connections are okay, replace the motor control board. If the problem continues, replace the main electronic control board. Parts named: wire harness, motor control board, main electronic control board.

Kenmore 110 model VMAX top-load washer code Er

Listed as control board error.

The electronic control board failed to save cycle information during a power failure. Press Stop/Cancel to clear the display and set a new cycle to finish the load.

Kenmore 110 model VMAX top-load washer code FL

Listed as overfill level reached.

Unplug the washer to see if it fills when the power is disconnected. If so, replace the water inlet valve assembly because a valve isn't shutting off water flow. If the washer isn't overfilled, replace the water level pressure switch because it isn't detecting water level accurately. Some models have a separate flood water level pressure switch to detect the overfill condition. Replace the flood water level pressure switch in those models. Parts named: water inlet valve assembly, water level pressure switch or flood water level pressure switch.

Kenmore 110 model VMAX top-load washer code Ld

Listed as long drain.

Check the house washer drain and clear any clogs.

Check the drain hose and clear any kinks or clogs. Unplug the washer and drain the tub using a wet/dry shop vac. Check the hose between the tub and the drain pump and clear any clogs. Check the drain pump and clear any clogs. If the drain pump doesn't run when activated, check the wire harness connections between the motor control board and the drain pump. or replace the wire harness if damaged. If the wire connections are okay, replace the drain pump. Parts named: drain pump, wire harness.

Kenmore 110 model VMAX top-load washer code LF

Listed as long fill.

Make sure the water supply faucets behind the washer are fully open.

Check the water fill lines for kinks or freezing in the winter. Check the water inlet valves. If the valves don't open when activated, unplug the washer and replace the water inlet valve assembly. Parts named: water inlet valve assembly.

Kenmore 110 model VMAX top-load washer code LS

Listed as lid switch error.

The LS code appears if you press Start with the lid open. Close the lid before starting the cycle. Replace the lid switch if it isn't accurately detecting whether the lid is open or closed. Parts named: lid switch.

Kenmore 110 model VMAX top-load washer code Ob

Listed as unbalanced load.

Open the lid and redistribute the clothes inside the basket. Restart the washer to finish the cycle.

Kenmore 110 model VMAX top-load washer code Or or Sr

Listed as failed relay on the main electronic control board.

Unplug the washer and replace the main electronic control board. Parts named: main electronic control board.

Kenmore 110 model VMAX top-load washer code PF

Listed as power failure.

The washer lost power during a cycle. Press Start to continue the cycle from the point that power was lost or press Stop/Cancel to clear the display and cancel the cycle.

Kenmore 110 model VMAX top-load washer code SL

Listed as excessive suds.

Use the correct amount of high efficiency detergent if you see excessive suds. Allow the washer to sit idle for 30 minutes to dissipate excessive suds and then run the Rinse/Spin cycle to drain the water. Start a new cycle without adding any detergent to rinse detergent out of the load. Parts named: HE detergent.

Kenmore 110 model VMAX top-load washer code heavy-duty-normal-slow-fill

Listed as slow fill.

Select only the Cold water temperature button when using the portable installation because you control water temperature using the sink faucets. Unplug the washer and check the water inlet valve screens for clogs. If a screen is clogged, replace the water inlet valve rather than cleaning the screen. Cleaning could allow debris to enter the valve, resulting in the valve sticking open and causing a flood. If an inlet valve won't open when activated, replace the defective water inlet valve. Parts named: water inlet valve.

Kenmore 110 model VMAX top-load washer code heavy-duty-normal-unexpected-fill-during-agitation-or

Listed as unexpected fill during agitation or soak.

This code will appear if you remove garments from the basket after the washer filled. Push the Start/Off button to reset the control. The control will fill the washer and resume the selected cycle. If you didn't remove any garments, then the tub could have a leak. Unplug the washer and check the tub, drain pump and drain hose for leaks. Replace any leaking components. Parts named: tub, drain pump, drain hose.

Kenmore 110 model VMAX top-load washer code heavy-duty-perm-incorrect-fill-water-level

Listed as incorrect fill water level.

Unplug the washer and check the wire harness connections between the water level pressure switch and the electronic control board. or replace the wire harness if damaged. If the wire harness connections are okay, check the air hose on the water level pressure switch for proper connection and damage. Reconnect the air hose if loose or replace it if damaged. If the wire connections and air hose are okay, replace the water level pressure switch. Parts named: water level pressure switch, air hose, wire harness.

Kenmore 110 model VMAX top-load washer code dL (F80, F82, F84 or F85)

Listed as lid lock failure.

Check for debris in the lid lock mechanism that could prevent it from locking.

Unplug the washer and check the wire harness connections for the lid lock/switch on the main electronic control board. Examine the lid lock/switch assembly. If it's damaged or defective, replace it. Parts named: lid lock/switch assembly.

• Debris in the lid lock mechanism that stops it locking: dL, F80, F82, F84 or F85 appears and the lid does not latch. Look into the lid lock for lint, a coin or a broken piece
• Loose wire harness connections for the lid lock/switch on the main electronic control board: The connector at the control board is loose or backed out. Unplug the washer and check the harness connections at the board
• A damaged or defective lid lock/switch assembly: The mechanism is clear and the wiring is good but the lid still does not lock. Examine the assembly and replace it if it is damaged or defective

Look for anything that could prevent it from locking, such as lint, a coin or a broken piece.

Reseat the connector on the control board and check the whole wire run up to the lid lock.

The chart names the lid lock/switch assembly as the only part, once the debris and the wiring have passed.

dL (F80, F82, F84 or F85) (110 model Oasis table).

Lid lock/switch assembly.

A screwdriver or nut driver and a flashlight.

What do dL, F80, F82, F84 and F85 mean? A lid lock failure, in the chart's words.

Are all five codes the same fault? The chart lists them on one row with the same steps.

How is dU different? dU or F83 is the lid failing to unlock.

Do not run the washer with a lid that will not lock

Unplug the washer before checking the lock wiring at the board

Kenmore 110 model VMAX top-load washer code dU or F83

Listed as lid unlock failure.

Unplug the washer. Check the wire harness connections for the lid lock/switch assembly on the main electronic control board. If the connections are okay, then you will typically need to force the lid open. This will usually break the lid lock/switch assembly. Replace the lid lock/switch assembly if it's damaged or broken. Parts named: lid lock/switch assembly.

• A loose wire harness for the lid lock/switch assembly on the main electronic control board: dU or F83 appears after a cycle and the lid stays locked. Unplug the washer and check the harness connections at the board
• A lid lock/switch that is stuck in the locked position: The wiring is good and the lid still will not open. The chart says you will typically need to force the lid open
• A lid lock/switch broken by forcing the lid: The lid was forced and the lock is now damaged. Replace the assembly if it is damaged or broken

Make sure the tub has stopped turning and the water is drained before you go on.

Reseat the connector on the control board and check the whole wire run up to the lid.

The chart says forcing the lid will usually break the assembly, so expect to replace it once the lid is open.

dU or F83 (110 model Oasis table).

A flat tool to release the lid and a screwdriver or nut driver.

What do dU and F83 mean on a Kenmore Oasis top-load washer? A lid unlock failure, in the chart's words.

Will I have to force the lid? The chart says that if the connections are okay you will typically need to.

Make sure the tub has stopped and drained before you force the lid

Unplug the washer and let the tub stop turning before forcing anything

Kenmore 110 model VMAX top-load washer code F02

Listed as user interface failure.

Unplug the washer. Open the console and check the wire harness connection between the main electronic control board and the user interface control board. If the wire harness connection is okay, then the user interface control board will need to be replaced. Parts named: user interface control board.

• A loose or damaged wire harness between the main electronic control board and the user interface control board: F02 appears and the console is dark or ignores keys. Unplug the washer, open the console and check the harness connection
• A failed user interface control board: The wire harness connection is okay and the code remains. The chart replaces the user interface control board if the harness is okay
• Moisture inside the console: The console was wet or the display is spotted. Look inside the console for damp or corroded contacts

Follow the service instructions for your model, and keep the screws together so the console goes back the same way.

Reseat the connectors at both ends of the harness, on the main board and on the user interface board.

The chart names the user interface control board as the only part for F02, once the harness connection has passed.

User interface control board.

If there is corrosion or liquid inside, dry it and check for damage before you power the washer again

Kenmore 110 model VMAX top-load washer code F40

Listed as water temperature thermistor failure.

The inlet water temperature thermistor (temperature sensor) is integrated into the inlet water valve assembly. Unplug the washer and check the wire harness connection between the main electronic control board and the thermistor on the inlet water valve assembly inside the console. If the wiring harness connection is okay, then the inlet water valve assembly will usually need to be replaced. Parts named: inlet water valve assembly.

• A loose or damaged wire harness between the main electronic control board and the thermistor on the inlet water valve assembly: F40 appears and the washer cannot judge the incoming water temperature. Unplug the washer and check the harness connection inside the console
• A failed inlet water temperature thermistor, which is integrated into the inlet water valve assembly: The wiring harness connection is okay and the code remains. The chart says the inlet water valve assembly will usually need to be replaced
• A damaged harness that gives an open or shorted reading: The plug is seated but a wire is worn. Inspect the harness before you order the valve assembly

Open the console only once the washer is fully disconnected, and keep the plug where you can see it.

at the thermistor connector and at the board, and check the plug is fully seated.

The chart says the inlet water temperature thermistor is integrated into the assembly, which will usually need to be replaced.

Inlet water valve assembly (includes the thermistor).

Where is the thermistor? Integrated into the inlet water valve assembly, according to the chart.

Do I replace the thermistor alone? No. It is integrated into the valve assembly.

The thermistor is part of the valve assembly, so expect to replace the whole assembly

Kenmore 110 model VMAX top-load washer code F41

Listed as motor RPS failure.

The motor RPS (Rotor Position Sensor) detects the speed of the drive motor. Unplug the washer and check the wire harness connections between the RPS and the main electronic control board. If the wire harness connections are okay, then the RPS will usually need to be replaced. Parts named: motor RPS sensor.

• Loose wire harness connections between the RPS and the main electronic control board: F41 appears and the motor speed is not being read. Unplug the washer and check the harness connections between the RPS and the board
• A failed motor RPS (Rotor Position Sensor), which detects the speed of the drive motor: The wiring connections are okay and the code remains. The chart says the RPS will usually need to be replaced
• A damaged RPS harness: The plug is seated but the wire is worn. Inspect the harness before you order a sensor

Use the plug and open the cabinet only when the washer is fully disconnected, and keep the plug in sight.

Reseat the connector at the RPS and at the board, and look for a wire that is pinched, burnt or backed out of its plug.

The chart says the RPS will usually need to be replaced once the wire harness connections have passed.

Motor RPS sensor.

What is the RPS? The Rotor Position Sensor, which detects the speed of the drive motor.

Unplug the washer before touching the motor wiring

F41 and F51 name the same sensor; F51 checks the basket first

Kenmore 110 model VMAX top-load washer code F44

Listed as heater relay failed.

On washers with a heating element, unplug the washer and replace the main electronic control board because the heater relay on that board is defective. For washers without a heating element, replace the user interface control board because a diode on the user interface control board is defective. If you just installed a new user interface control board when this code appears, then you likely installed an incompatible user interface control board. Check the user interface control board part number and then order and install the correct part. Parts named: main electronic control board, user interface control board.

• On a washer with a heating element, a defective heater relay on the main electronic control board: F44 appears on a washer model that has a heating element. The chart replaces the main electronic control board because the heater relay is defective
• On a washer without a heating element, a defective diode on the user interface control board: F44 appears on a washer model that has no heating element. The chart replaces the user interface control board
• A new user interface control board that is incompatible: F44 appeared right after a new user interface control board was fitted. Check the part number and order the correct part

The chart's repair depends on it, so check your full model number and the specification sheet for a heater.

The heater relay on that board is defective, so the board is the part to replace on a heated model.

A diode on that board is defective. If you just installed a new one, you likely fitted an incompatible board, so check the part number and order the correct part.

Main electronic control board and user interface control board.

Your model number, a parts list and a screwdriver or nut driver.

Which board is replaced? The main electronic control board if the washer has a heating element; the user interface control board if it does not.

Can a new board cause it? Yes. A new user interface control board that is incompatible can give F44.

Unplug the washer before opening the console or the board cover

Confirm whether your model has a heater before you order a board, since the chart splits the repair by that

Kenmore 110 model VMAX top-load washer code F50

Listed as motor stalled.

The motor RPS (Rotor Position Sensor) detects no rotation of the drive motor. Unplug the washer. Check to see if the basket spins freely. If not, then examine the drive system and eliminate the cause of friction. If the basket spins freely, check the wire harness connections between the main electronic control board and the motor. If the wire harness connections are okay, check the drive motor. If the motor is defective, replace it. Parts named: drive motor, wire harness.

• Friction in the drive system that stops the basket turning: F50 appears and the basket does not spin freely by hand. Unplug the washer and check whether the basket spins freely
• Loose or damaged wire harness connections between the main electronic control board and the motor: The basket spins freely but the motor does not turn. Check the wire harness connections between the board and the motor
• A defective drive motor: The basket spins freely and the wiring is okay. The chart replaces the drive motor if it is defective

The chart says the motor RPS detects no rotation of the drive motor for F50.

Look for a stuck garment between the basket and the tub, or a worn drive part that binds the basket.

Replace the drive motor if it is defective. The chart names the drive motor and the wire harness.

Drive motor and wire harness.

Unplug the washer before touching the drive system or the motor wiring

The drive motor is a costly part, so clear any friction and check the wiring first

Kenmore 110 model VMAX top-load washer code F51

Listed as motor RPS failure.

The motor RPS (Rotor Position Sensor) detects the speed of the drive motor. Check to see if the basket spins freely. If not, then examine the drive system and eliminate the cause of friction. If the basket spins freely, unplug the washer and check the wire harness connections between the RPS and the main electronic control board. If the wire harness connections are okay, then the RPS will usually need to be replaced. Parts named: motor RPS sensor.

• Friction in the drive system that stops the basket spinning freely: F51 appears and the basket does not spin freely by hand. Check to see whether the basket spins freely by hand
• Loose wire harness connections between the RPS and the main electronic control board: The basket spins freely and the speed is not read. Unplug the washer and check the harness connections between the RPS and the board
• A failed motor RPS (Rotor Position Sensor): The wiring connections are okay and the code remains. The chart says the RPS will usually need to be replaced

If it does not, examine the drive system and eliminate the cause of the friction you find.

Reseat the connector at the RPS and at the board, and look for a wire that is pinched, burnt or backed out of its plug.

The chart says the RPS will usually need to be replaced once the wire harness connections have passed.

Motor RPS sensor.

Unplug the washer before touching the drive system or the RPS wiring

F41 names the same sensor but skips the free-spin check

Kenmore 110 model VMAX top-load washer code F52

Listed as motor stop failure.

Drive motor failed to stop after the stop command from the main electronic control board. This is caused by a failure in the main electronic control board. The main electronic control board will usually need to be replaced to fix this failure. Parts named: main electronic control.

• A failure in the main electronic control board that leaves the motor running after a stop command: F52 appears and the drive motor keeps running when it should stop. The chart names the board, so confirm the motor really did not stop
• A one-off fault that clears with a reset: F52 appears once and then does not return afterwards. Unplug the washer for several minutes and run a short cycle
• A power surge that damaged the control board: The code followed a storm, an outage or a breaker trip. Note whether other appliances on the circuit were affected

The drive motor failed to stop after the stop command from the main electronic control board.

If F52 does not return after a short cycle, the fault was a one-off and needs no repair.

The chart says this is caused by a failure in the board, which will usually need to be replaced.

Main electronic control board.

Is the motor at fault? Not by the chart; it points at the board.

Unplug the washer at once if the drive motor keeps running after the stop command

The board is a costly part, so price it against the age of the washer before ordering

Kenmore 110 model VMAX top-load washer code F53

Listed as motor control over-temperature.

The motor control portion of the main electronic control board is overheating. This can be caused by a high current draw through the motor circuit due to excessive friction in the drive system. Check to see if the basket spins freely. If not, examine and repair the cause of the excessive friction. If the basket spins freely, then the drive motor and/or the main electronic control board may need to be replaced. Parts named: drive motor, Main electronic control board.

• Excessive friction in the drive system that makes the motor draw high current: F53 appears and the basket does not spin freely. Check to see whether the basket spins freely by hand
• A drive motor that is defective: The basket spins freely and the code still remains afterwards. The chart says the drive motor and/or the board may need to be replaced
• A main electronic control board that is overheating: The motor control portion of the board gets hot. The chart names the board with the drive motor

The chart says the motor control portion of the board is overheating, and high current through the motor circuit from friction can cause it.

Look for a stuck garment between the basket and the tub, or a worn drive part that binds the basket.

Replace one at a time and test between them, so you know which part was at fault.

Drive motor and main electronic control board.

Let the washer cool with the power off before you open it

The chart does not say which of the motor or the board fails, so a technician can test them

Kenmore 110 model VMAX top-load washer code F54

Listed as motor control overcurrent.

The motor control portion of the main electronic control board is drawing high current. This can be caused by excessive friction in the drive system. Check to see if the basket spins freely. If not, examine and repair the cause of the excessive friction. If the basket spins freely, then the drive motor and/or the main electronic control board may need to be replaced. Parts named: drive motor, Main electronic control board.

• Excessive friction in the drive system that makes the motor draw high current: F54 appears and the basket does not spin freely. Check to see whether the basket spins freely by hand
• A drive motor that is defective: The basket spins freely and the code still remains afterwards. The chart says the drive motor and/or the board may need to be replaced
• A main electronic control board that is drawing high current: The motor control portion of the board is faulty. The chart names the board with the drive motor

The chart says the motor control portion of the board is drawing high current, which excessive friction in the drive system can cause.

Remove anything stuck between the basket and the tub and check the drive parts for wear or damage.

Replace one at a time and test between them, so you know which part was at fault.

Drive motor and main electronic control board.

Unplug the washer before checking the drive system

The chart does not say which of the motor or the board fails, so a technician can test them

Kenmore 110 model VMAX top-load washer code F72

Listed as basket re-engagement failure.

The basket fails to engage the drive system for the spin mode. Check to see if the water drained out. If not, run a drain & spin routine to evacuate the water. If the basket still won't engage, check the drive system for an obstruction or failure. Parts named: drive system components.

• Water left in the tub that stops the basket engaging the drive: F72 appears and the tub still holds a lot of water. Check to see whether the water drained out
• The basket failing to engage the drive system for the spin mode: The tub is empty and the basket still does not engage. Check the drive system for an obstruction or failure
• An obstruction or failed drive system component: The basket turns freely but will not lock to the drive. Inspect the drive system components closely for damage

The chart says the basket fails to engage the drive system for the spin mode.

This clears the water so that the basket can try to engage the drive again on the next spin.

The chart names the drive system components as the parts, so a technician can tell which one failed.

Drive system components.

How do I clear the water? Run a drain and spin routine, per the chart.

Unplug the washer before checking the drive system

The chart names only drive system components, so a technician can identify which part failed

Kenmore 110 model VMAX top-load washer code HC

Listed as hot & cold fill hoses are reversed.

Check the positions of the fill hoses on the back of the washer.

If they are reversed, then connect them properly.

• The hot and cold fill hoses are connected to the wrong faucets: HC appears and hot water arrives where cold is expected. Check the positions of the fill hoses on the back of the washer
• Hoses that were swapped after a move or a plumbing job: The code began after the washer was moved or the hoses were changed. Compare the hoses with the faucets they are connected to
• Hot and cold faucets that are labeled the wrong way in the house: The hoses match the labels but the water is reversed. Run each faucet and feel which is hot

The chart's whole check for HC. The hot hose belongs on the hot inlet and the cold hose on the cold inlet.

Shut the faucets, unscrew each hose and swap them so hot is on hot, then open the faucets and check for leaks.

The chart names no part for HC, so a correct hose connection should clear it without any parts.

HC (110 model Oasis table).

None.

Towels and pliers or a hose wrench.

What does HC mean on a Kenmore Oasis top-load washer? The hot and cold fill hoses are reversed, in the chart's words.

How is it different from the VMW F8 E5? The VMW chart also names the inlet thermistor if the hoses are right; the Oasis chart does not.

Does a reversed hose damage the washer? The chart does not say so. It treats HC as a connection to correct and names no part, so swapping the hoses to the right inlets is the whole repair, followed by a short cycle to confirm the code has gone.

Do not touch very hot water from the hose; let it run and check with care

Shut the faucets before you unscrew a hose

Kenmore 110 model VMAX top-load washer code Ld or F32

Listed as long drain time.

This code is displayed when the water level does not change after the drain pump runs. If the washer does not drain, check the drain hose and washer drain for a clog or restriction. Unplug the washer and check the drain pump for a clog. If the drain pump is defective, replace it. If the washer is draining properly and the drop in water level isn't being detected, then the main electronic control board will need to be replaced. Parts named: drain pump, Main electronic control board.

• A clog or restriction in the drain hose or the washer drain: Ld or F32 appears and water stays in the tub after the pump runs. Check the drain hose and the washer drain for a clog or restriction
• A clogged or defective drain pump: The drain path is clear but water does not leave. Unplug the washer and check the drain pump for a clog
• The washer is draining properly but the water level drop isn't being detected: The tub empties normally and the code still appears. The chart says the main electronic control board will need to be replaced

The chart says the code shows when the water level does not change after the drain pump runs, so start with the drain path.

If the drain pump is defective, replace it, once the hose and the drain have been cleared and tested.

The chart names the main electronic control board as the part when the tub really empties, so nothing else is replaced first.

Ld or F32 (110 model Oasis table).

Drain pump and main electronic control board.

A shallow pan, towels and a screwdriver or nut driver.

What do Ld and F32 mean on a Kenmore Oasis top-load washer? A long drain time: the water level does not change after the drain pump runs.

What if the tub drains fine? Then the level drop is not being detected and the chart replaces the board.

Unplug the washer and bail out the tub before working at the pump

Do not keep running cycles with a tub that will not empty

Kenmore 110 model VMAX top-load washer code LF or F30

Listed as long fill.

If water isn't entering the washer, make sure that the water supply faucets are fully open. Check the fill hoses for kinks or freezing (in the winter). Check the inlet water valve screens for debris or deposits. Replace the inlet water supply valve assembly if the screens are clogged. If water is entering the tub but not being detected properly, then check the air hose between the bottom of the tub and the connection on the main electronic control board. If the air hose connection is okay, replace the main electronic control board (the water level sensor is a component of the main electronic control board). Parts named: inlet water valve assembly, Main electronic control board.

• The water supply faucets are not fully open: LF or F30 appears and water is not entering the washer. Make sure the water supply faucets are fully open
• Kinked or frozen fill hoses: The hoses are bent behind the washer or the house is cold enough to freeze water lines. Check the fill hoses for kinks or freezing in winter
• Debris or deposits on the inlet water valve screens: The hoses flow but the tub still fills slowly. Check the inlet water valve screens for debris or deposits
• Water entering the tub but not being detected: The tub fills normally but the code appears on the display anyway. Check the air hose between the bottom of the tub and the main electronic control board

Then check the fill hoses behind the washer for kinks, and in the winter for freezing that stops the flow.

The chart replaces the inlet water supply valve assembly if the screens are clogged, and does not clean the screens.

The hose runs between the bottom of the tub and the board. If it is okay, replace the board, because the water level sensor is a component of it.

LF or F30 (110 model Oasis table).

Inlet water valve assembly and main electronic control board.

Towels and a screwdriver or nut driver.

What do LF and F30 mean on a Kenmore Oasis top-load washer? A long fill, in the chart's words.

Where is the water level sensor? It is a component of the main electronic control board, per the chart.

Shut the faucets if a hose leaks or the tub overfills

The board is the last and costliest part, so check the supply, the screens and the air hose first

Kenmore 110 model VMAX top-load washer code lid or F81

Listed as lid not closed or lid not opened between cycles.

This code appears if you press start with the lid open. It will also appear is you press Start after 2 consecutive cycles without opening the lid. If the lid lock/switch assembly isn't properly detecting the position of the washer lid (open/closed), then replace it. Parts named: lid lock/switch assembly.

• Start was pressed with the lid open: The lid code appears right after pressing Start and the lid was not fully down. Close the lid fully and then press Start again
• Start was pressed after 2 consecutive cycles without opening the lid: The washer was run twice without the lid being opened. Open and close the lid between two cycles
• A lid lock/switch assembly that does not detect the lid position: The lid opens and closes properly and the code returns. The chart replaces the assembly if it isn't properly detecting the lid

The chart says the code appears if you press Start with the lid open, so make sure the lid is down and latched first.

It also appears if you press Start after 2 consecutive cycles without opening the lid.

The chart names the lid lock/switch assembly as the only part for this code, and replaces it only if it fails to detect the lid.

lid or F81 (110 model Oasis table).

What do lid and F81 mean on a Kenmore Oasis top-load washer? The lid is not closed, or was not opened between cycles.

Is it always a fault? No. Closing the lid or opening it between cycles often clears it.

Do not bypass the lid switch, since the basket must not spin with the lid open

Unplug the washer before touching the lid lock/switch assembly

Kenmore 110 model VMAX top-load washer code oL or F70

Listed as overloaded.

The size of the load exceeds the washers capacity. Open the lid and remove some garments. Restart the cycle.

• The load exceeds the washer's capacity: oL or F70 appears and the tub is packed to the top. Open the lid and look at how full the tub is
• Heavy items such as blankets or wet towels: The tub looks half full but the items are very heavy. Remove some of the heaviest wet garments from the tub
• A load that has absorbed a lot of water: The code appears after a fill in a load of very absorbent fabric. Remove some garments from the tub and restart the cycle

The chart's repair is to take out part of the load. Start with the heaviest, wettest items.

Close the lid and start the cycle again. A smaller load should run through without the code coming back.

Wash bulky items such as comforters alone so that the tub is not overloaded again on the next load.

oL or F70 (110 model Oasis table).

None.

None.

What do oL and F70 mean on a Kenmore Oasis top-load washer? Overloaded: the size of the load exceeds the washer's capacity.

Is it the same as uL? No. uL is an unbalanced load; oL is a load that is too large.

How full should the tub be? The chart gives no weight limit, only that the size of the load exceeds the washer's capacity. A tub packed to the top is too full, so fill it loosely and wash blankets and comforters on their own.

If the code appears with a normal small load, the fault is probably not the load; see the F50 to F54 motor pages

Stop and unplug the washer if the lid will not open because of a full tub

Kenmore 110 model VMAX top-load washer code Sd or F71

Listed as excessive suds.

Sd is displayed steady on when excessive suds is detected. The washer conducts a routine to eliminate the excessive suds. If the suds cannot be eliminated, then the Sd flashes in the display. Let the suds dissipate and then drain the washer. Use only the appropriate quantity of HE (High Efficiency) detergent in the washer. Parts named: HE detergent.

• Too much detergent or the wrong kind of detergent: Sd is steady on and foam rises in the tub. Check which detergent was used and how much
• Suds that the washer cannot eliminate on its own: Sd flashes after the washer's suds routine has run. Let the suds dissipate and then drain the washer
• Detergent that is not high efficiency: The detergent box has no HE mark on it. Use only the appropriate quantity of HE detergent

The chart says Sd is displayed steady on when excessive suds is detected, and the washer conducts a routine to eliminate them.

A flashing Sd means the routine could not eliminate the suds, so give the foam time to settle before you drain.

The chart names HE detergent as the only fix, so no part is replaced for Sd.

Sd or F71 (110 model Oasis table).

HE detergent; no part.

A measuring cup.

What do Sd and F71 mean on a Kenmore Oasis top-load washer? Excessive suds, in the chart's words.

Stop and unplug the washer if suds have spilled into the console or onto the floor

Do not add more detergent to fight suds, because that only makes more

Kenmore 110 model VMAX top-load washer code uL

Listed as unbalanced load.

This code is steady on when an unbalanced load is detected and the washer runs a mini-cycle routine to balance the load. If the load cannot be balanced by that routine, then uL will flash and the door will unlock. You can redistribute the load and start the washer. If the tub bangs violently even with a balanced load then you may have a damaged suspension rod/spring assembly. Replace the suspension rods/springs in that situation. Parts named: suspension Rods/Springs (replacement part has a set of 4 rods/springs -- replace all of them at once).

• An unbalanced load that the washer is trying to balance: uL is steady on and the washer runs a mini-cycle routine. Wait for the mini-cycle routine to finish, then see whether uL clears
• A load that cannot be balanced by the routine: uL flashes and the door unlocks after the routine. Redistribute the load evenly and start the washer again
• A damaged suspension rod/spring assembly: The tub bangs violently even with a balanced load. The chart replaces the suspension rods and springs in that situation

The chart says uL is steady on while an unbalanced load is detected and the washer runs a mini-cycle routine to balance the load.

A flashing uL means the routine could not balance the load and the door has unlocked.

The replacement part has a set of 4 rods and springs, and the chart says to replace all of them at once.

uL (110 model Oasis table).

Suspension rods/springs, a set of 4.

A screwdriver or nut driver and a level.

What does uL mean on a Kenmore Oasis top-load washer? An unbalanced load, in the chart's words.

What is the difference between steady and flashing? Steady means the washer is running its balance routine; flashing means it could not balance the load.

Do I replace one rod? No. The chart says to replace all four at once.

Stop the spin and unplug the washer if the cabinet is walking across the floor

The replacement part is a set of 4 rods and springs, and the chart says to replace all of them at once

Kenmore 110 model VMAX top-load washer code F0 E2

Listed as excessive suds.

Use only HE (High Efficiency) detergent. Reduce the quantity of detergent to prevent excessive suds. Parts named: HE detergent.

• Regular detergent used in a vertical modular washer that needs HE detergent: The display shows F0 E2 and foam rises in the tub. Check the detergent label for the HE mark
• Too much HE detergent for the load: Foam appears even with the right detergent and a small load. Reduce the quantity of detergent as the chart says
• Detergent residue building up over many loads: Suds return on the next few loads despite a smaller dose. Run a rinse cycle and see whether foam returns

The chart's first instruction. Regular detergent makes far more suds than this washer's control expects.

Use less than the label's maximum dose, especially with small loads, to prevent excessive suds and foam.

Let the washer finish and check that the tub is clear of foam before the next load.

F0 E2 (110 model VMW table).

HE detergent; no part.

A measuring cup.

Is it the same on the VMAX? The VMAX chart words it as Sd or F0 E2 and asks for the right amount of HE detergent.

Why does this washer react to so many suds? The chart's fix is HE detergent in a smaller quantity, because a vertical modular washer uses little water and cannot rinse away the foam that regular detergent makes. Measure the dose against the load size each time.

Stop and unplug the washer if suds have spilled into the console or onto the floor

Do not add more detergent to fight suds, because that only makes more

Kenmore 110 model VMAX top-load washer code F0 E4

Listed as high water temperature in the rinse cycle.

Make sure that fill hoses are properly connected.

Check the resistance of the thermistor (temperature sensor). It should measure around 50K ohms (50,000 ohms) at 77 degrees. If the thermistor is defective, replace it. Parts named: thermistor.

• Fill hoses that are connected the wrong way round or loosely: F0 E4 appears in the rinse and the rinse water is hot when it should be cold. Make sure the fill hoses are properly connected, hot to hot and cold to cold
• An inlet thermistor that reads wrongly: The hoses are right and the control still sees hot rinse water. Measure the thermistor; the chart expects around 50,000 ohms at 77 degrees
• A hot valve that leaks hot water into the rinse: The rinse water is warm even with cold selected. Check the water temperature during a cold rinse

Hot hose on the hot faucet and cold hose on the cold faucet. A reversed pair gives a hot rinse.

The chart says it should measure around 50,000 ohms at 77 degrees. Unplug the washer and measure it with a multimeter.

The chart names the thermistor as the only part for F0 E4 on the VMW.

Thermistor.

A multimeter and a screwdriver or nut driver.

Does F0 E4 mean the water is dangerously hot? The chart only says the rinse water temperature is high. Check the hose connections first, and let the tub cool before touching the water if it feels hot; the thermistor test decides whether a part has failed.

Unplug the washer before you measure the thermistor

Do not touch the water if it feels hot; let the tub cool first

Kenmore 110 model VMAX top-load washer code F1 E2

Listed as motor control error on main electronic control board failure.

Unplug the washer. Check the wiring connections on the main electronic control board and the drive motor. If the wiring connections are okay, then the drive motor windings will need to be checked for resistance. If the drive motor is bad, replace it. If the drive motor is okay, the main electronic control board will usually need to be replaced. Parts named: drive motor, Main electronic control board.

• Loose wiring connections on the main electronic control board or the drive motor: F1 E2 appears and the motor does not run normally. Unplug the washer and check the wiring connections at both ends
• Bad drive motor windings: The wiring is okay and the winding resistance is wrong. Check the drive motor windings for resistance, as the chart says
• A failed main electronic control board: The drive motor is okay and the code remains. The chart says the board will usually need to be replaced if the motor is okay

Reseat every connector at both ends of the motor harness, on the board and on the drive motor.

If the wiring connections are okay, the chart has you measure the windings. If the drive motor is bad, replace it.

The chart says the board will usually need to be replaced in that case, after the motor has passed its winding test.

Drive motor and main electronic control board.

Unplug the washer before touching the motor wiring

Replace one part at a time, since the motor and the board are both costly

Kenmore 110 model VMAX top-load washer code F2 E1

Listed as stuck key.

This code is for models with a digital display. One or more keys on the user interface were actuated for 15 seconds or longer. If a key is stuck and cannot be freed up then the user interface control will need to be replaced. Parts named: user interface control.

• One or more keys on the user interface were held for 15 seconds or longer: F2 E1 appears on a digital display model and a key feels jammed. Press each key and see whether any stays down
• Moisture or residue holding a key: The console is damp or sticky near the keys. Dry and clean the console and try the key again
• A failed user interface control with a shorted key: The key cannot be freed by hand however much you work it. The chart replaces the user interface control if a key is stuck and cannot be freed

The chart says this code is for models with a digital display, so check your model before you order a control.

One or more keys were actuated for 15 seconds or longer. Work each key and clean around it.

The chart names the user interface control as the only part for F2 E1, and replaces it only if the key cannot be freed.

User interface control.

Which models does it apply to? Models with a digital display, according to the chart.

How long is the key press limit? 15 seconds, per the chart.

Unplug the washer if liquid has run behind the console

This code is for models with a digital display, so confirm your model before ordering a control

Kenmore 110 model VMAX top-load washer code F2 E3

Listed as mismatch of main electronic control board and user lnterface control.

This code is for models with a digital display. It typically occurs when an incompatible control component (Main Electronic Control board or User Interface control) is replaced in the console. Check the replacement part numbers and reorder the correct part. Parts named: main electronic control board, User interface control.

• An incompatible main electronic control board was fitted: F2 E3 appeared right after the board was replaced in the console. Compare the board's part number with the one for your model number
• An incompatible user interface control was fitted: F2 E3 appeared right after the user interface control was replaced. Compare the control's part number with the one for your model number
• A replacement from a similar washer with different software: The part looks identical but its stamped number differs from the list. Look up your full model number in a parts list

The chart says this code typically occurs when an incompatible control component, the main electronic control board or the user interface control, is replaced in the console.

Compare each stamped number with your model's parts list before you order or refit anything.

Unplug the washer before you open the console and refit the correct part. This code is for models with a digital display.

Main electronic control board and user interface control.

Your model number, a parts list and a screwdriver or nut driver.

Stop refitting parts until the numbers match your model number

Return a part the seller cannot match to your washer

Kenmore 110 model VMAX top-load washer code F3 E1

Listed as water level pressure sensor fault.

Unplug the washer. Check the air hose connection between the bottom of the tub and the water level pressure switch on the main electronic control board in the console. If no problems are found, then the main electronic control board (which includes the water level pressure switch) will usually need to be replaced. Parts named: main electronic control board.

• A problem with the air hose connection between the bottom of the tub and the water level pressure switch: F3 E1 appears and the washer misjudges the water level. Unplug the washer and check the air hose connection at both ends
• A kinked, split or blocked air hose: The hose looks flattened, cracked or has water in it. Look along the whole air hose for damage
• A failed main electronic control board, which includes the water level pressure switch: The air hose is sound and the code remains. The chart says the board will usually need to be replaced if no problems are found

The hose runs between the bottom of the tub and the water level pressure switch on the main electronic control board in the console.

A damaged hose gives the same fault as a failed pressure switch, so check it before you replace the board.

The chart says the board, which includes the water level pressure switch, will usually need to be replaced.

Main electronic control board (includes the water level pressure switch).

Where is the pressure switch? On the main electronic control board in the console, according to the chart.

Unplug the washer before working in the console

The board is a costly part, so check the hose carefully first

Kenmore 110 model VMAX top-load washer code F3 E2

Listed as inlet water temperature fault.

Unplug the washer. Open the console and check the resistance through the thermistor circuit (black wires). It should measure around 50K ohms (50,000 ohms) at room temperature. If the thermistor is defective, replace it (the thermistor is a component in the inlet valve assembly wiring harness). Parts named: inlet water valve wiring harness (this harness includes the thermistor).

• An inlet thermistor whose resistance is off: F3 E2 appears and the washer cannot judge the incoming water temperature. Open the console and check the thermistor circuit on the black wires; it should read about 50,000 ohms
• A damaged wire in the inlet valve wiring harness: The thermistor reads open or shorted when the harness is moved. Inspect the harness for damage before you order a part
• A failed thermistor in the harness: The reading is far from 50,000 ohms at room temperature. The chart replaces the inlet water valve wiring harness, which includes the thermistor

Find the thermistor circuit, which is the black wires in the inlet valve wiring harness.

It should measure around 50,000 ohms at room temperature, per the chart, so note the reading you get.

The chart says the thermistor is a component in the inlet valve assembly wiring harness, so the harness is the part.

Inlet water valve wiring harness (includes the thermistor).

What should the thermistor circuit measure? Around 50K ohms (50,000 ohms) at room temperature.

Which wires are tested? The black wires of the thermistor circuit.

Unplug the washer before you open the console panel

The thermistor is a component in the harness, so it is replaced with the harness

Kenmore 110 model VMAX top-load washer code F5 E1

Listed as lid switch fault.

This code is displayed if Start is pressed with the lid open. If the lid switch on the lid lock/switch assembly isn't detecting the condition of the washer lid properly, then the lid lock/switch assembly will need to be replaced. Parts named: lid lock/switch assembly.

• Start was pressed with the lid open: F5 E1 appears right after pressing Start and the lid was not fully down. Close the lid fully and press Start again
• A lid switch on the lid lock/switch assembly that does not detect the lid properly: The lid is closed and the washer still reads it as open. The chart replaces the lid lock/switch assembly if the switch does not detect the lid
• A lid that does not seat fully because of a bent hinge or an item in the way: The lid sits slightly proud of the cabinet when closed. Check the lid seats flat with nothing under it

The code is displayed if Start is pressed with the lid open, so try again with the lid down.

A bent hinge or an item under the lid keeps the switch from closing, so look along the whole lid edge.

The chart names the lid lock/switch assembly as the only part for F5 E1, and replaces it only if the switch fails to detect the lid.

Lid lock/switch assembly.

Do not bypass the lid switch, since the basket must not spin with the lid open

Unplug the washer before touching the lid lock/switch assembly

Kenmore 110 model VMAX top-load washer code F5 E2

Listed as lid lock fault.

Unplug the washer. Check the lid lock/switch assembly for debris or an item that is interfering with the lock strike being engaged by the lid lock mechanism. If no interference is apparent, then the lid lock/switch assembly will usually need to be replaced. Parts named: lid lock/switch assembly.

• Debris or an item interfering with the lock strike being engaged by the lid lock mechanism: F5 E2 appears and the lid will not lock. Unplug the washer and check the lid lock/switch assembly and strike for debris
• A worn or damaged lock strike: The strike is bent or worn and the latch does not catch. Look at the strike on the lid for wear or damage
• A failed lid lock/switch assembly: No interference is apparent and the lock still does not engage. The chart says the assembly will usually need to be replaced

Do not check the lock with the washer powered, and keep the plug where you can see it.

Look at the strike on the lid and the lock mechanism it engages, and clear anything that blocks it.

The chart says the assembly will usually need to be replaced at this point, since no interference is apparent.

Do not run the washer with a lid that will not lock

Unplug the washer before checking the lock assembly

Kenmore 110 model VMAX top-load washer code F5 E3

Listed as lid unlock fault.

Unplug the washer. Lift the top panel of the washer to access the lid lock/switch assembly. Try to manually unlock the washer lid without breaking the lid lock/switch assembly and the lock strike. If the components are damaged, replace them. If the lid lock/switch assembly won't lock and unlock properly, replace it. Parts named: lid lock/switch assembly, Lock strike.

• The lid lock/switch assembly is stuck and will not release the lid: F5 E3 appears and the lid stays locked after the cycle. Unplug the washer and lift the top panel to reach the assembly
• A damaged lock strike: The strike is bent or jammed in the lock. Try to unlock the lid manually without breaking the assembly or the strike
• A lid lock/switch assembly that will not lock and unlock properly: The assembly moves stiffly or not at all when tested. Replace the assembly if it will not lock and unlock properly

The chart has you lift the top panel of the washer to reach the lid lock/switch assembly.

Work gently and do not force it. If the components are damaged or broken, replace them.

The chart names the lid lock/switch assembly and the lock strike as the parts for F5 E3.

Lid lock/switch assembly and lock strike.

A putty knife or screwdriver to lift the top panel.

How do I release the lid? Unplug the washer, lift the top panel and try to manually unlock the lid without breaking the assembly and the strike.

How is it different from the VMAX F5 E3? The VMAX chart says to force the lid open; the VMW chart tries to unlock it manually without breaking the parts.

Make sure the basket has stopped and the tub is drained before working at the lid lock

Unplug the washer before lifting the top panel

Kenmore 110 model VMAX top-load washer code F5 E4

Listed as lid not opened between cycles.

If the washer is started several times without the lid ever being opened, then this code appears. If the lid is actually being opened between cycles but the control doesn't detect it, then the door lock/switch assembly will typically need to be replaced. Parts named: lid lock/switch assembly.

• The washer was started several times without the lid ever being opened: F5 E4 appears at the start of a later load and the lid was left shut. Open and close the lid between loads and start the cycle
• A lid that is opened between cycles but the control does not detect it: The lid opens normally and the code returns anyway. The chart says the assembly will typically need to be replaced in this case
• A lid lock/switch assembly whose switch is stuck: The switch never registers the lid opening at all. Test the lid opening several times and see whether the code follows

The code appears if the washer is started several times without the lid ever being opened, so open and close the lid and restart.

If the lid is actually being opened but the code returns, the switch is not registering it.

The chart says the door lock/switch assembly will typically need to be replaced in that case.

Unplug the washer before touching the lid lock/switch assembly

Do not bypass the switch to force a cycle to start

Kenmore 110 model VMAX top-load washer code F7 E1

Listed as basket speed sensor fault.

See if the spin basket rotates freely.

If not, then examine and replace any defective drive components. If the basket spins properly, unplug the washer and check the wiring connections on the shifter assembly. That component has the optical tachometer. If the wiring connections are okay, then that shifter will usually need to be replaced. Parts named: drive system components, shifter assembly.

• The spin basket does not rotate freely: F7 E1 appears and the basket feels stiff or rough when turned by hand. See whether the spin basket rotates freely by hand
• A defective drive component that creates friction: The basket binds or makes noise when turned by hand. Examine the drive components and replace any that are defective
• Loose wiring on the shifter assembly, which contains the optical tachometer: The basket spins properly but the speed is not read. Unplug the washer and check the wiring connections on the shifter assembly
• A failed shifter assembly: The wiring connections are okay and the code remains. The chart says the shifter will usually need to be replaced

If it does not, examine the drive system and replace any defective drive components you find.

The shifter assembly has the optical tachometer that reads basket speed, so a loose plug there stops the speed reading.

The chart says the shifter will usually need to be replaced at this point, after the wiring connections have passed.

Drive system components and shifter assembly.

What is the optical tachometer? The chart says the shifter assembly has it; it reads the basket's speed.

Unplug the washer before checking the wiring or reaching under the tub

The shifter is a specialised part; consider a technician if you have not opened this washer before

Kenmore 110 model VMAX top-load washer code F7 E5

Listed as shifter assembly fault.

The main electronic control board cannot determine the position of the drive system shifter. Unplug the washer and check the wiring harness connections on the main electronic control board and the shifter assembly. If the wiring connections are okay, then the shifter assembly will usually need to be replaced. Parts named: shifter assembly.

• Loose wiring harness connections on the main electronic control board or the shifter assembly: F7 E5 appears and the control cannot tell the shifter position. Unplug the washer and check the wiring harness connections at both ends
• A failed shifter assembly: The wiring connections are okay and the code remains. The chart says the shifter assembly will usually need to be replaced
• A jam in the shifter mechanism: The shifter will not move between wash and spin. Look for anything that is blocking the shifter's travel

The chart's first step. The shifter sits under the tub and is reached from below or behind.

Reseat every connector on the board and on the shifter, and look for a worn wire.

The chart says the main electronic control board cannot determine the position of the drive system shifter, and names the shifter assembly as the part.

Shifter assembly.

Unplug the washer before you check the wiring

The shifter is a specialised part; consider a technician if you have not opened this washer before

Kenmore 110 model VMAX top-load washer code F7 E6

Listed as motor fault.

Unplug the washer and check the wiring connections on the drive motor. If the wiring connections are okay, then the drive motor will typically need to be replaced. Parts named: drive motor.

• Loose wiring connections on the drive motor: F7 E6 appears and the motor does not run. Unplug the washer and check the wiring connections on the drive motor
• A failed drive motor: The wiring connections are okay and the motor still does not run. The chart says the drive motor will typically need to be replaced
• A damaged motor harness: The plug is seated but the wire is worn. Look along the whole motor harness for damage

Use the plug and open the cabinet only when the washer is fully disconnected, and keep the plug in sight.

Reseat the connector at the motor and look for a wire that is pinched, burnt or backed out of its plug.

The chart says the drive motor will typically need to be replaced, and names it as the only part for F7 E6.

Drive motor.

Can I test the drive motor myself? The chart gives no resistance figure for F7 E6. It goes from the wiring connections on the drive motor straight to replacing the motor, so a technician with the model's service sheet is the person to measure it.

Unplug the washer before touching the motor wiring

The drive motor is a costly part, so check the wiring carefully first

Kenmore 110 model VMAX top-load washer code F7 E7

Listed as motor is unable to reach target RPM.

Rotate the spin basket to see if it spins freely. If not, then a garment could be stuck between the outer tub and the spin basket. A problem with drive components could also cause excess friction. Inspect the drive components and replace parts as needed. Parts named: drive system components.

• A garment stuck between the outer tub and the spin basket: F7 E7 appears in spin and the basket is slow or noisy. Rotate the spin basket to see whether it spins freely
• A problem with the drive components that causes excess friction: The basket binds or grinds when turned by hand. Inspect the drive components and replace parts as needed
• A load that binds the basket: The load is heavy and wedged against the tub. Unload the washer and try the basket again

Unplug the washer and turn the basket by hand, feeling for any rough or tight spot as it goes round.

Use a flashlight to look into the gap and take out anything wedged there, such as a bra wire or a small garment.

The chart says a problem with the drive components could also cause excess friction, so replace whichever part is worn.

Drive system components.

A flashlight and a screwdriver or nut driver.

Can a garment cause it? Yes. A garment stuck between the outer tub and the spin basket adds friction.

Unplug the washer before reaching between the tub and the basket

The chart names only drive system components, so a technician can identify which is worn

Kenmore 110 model VMAX top-load washer code F8 E1

Listed as not filling or long fill time.

Water isn't being detected as entering the washer. If the washer isn't filling, check the water supply faucets behind the washer to make sure that they are fully open. Check the fill hoses and inlet water valves. If the inlet water valve assembly is defective, replace it. If water is entering the machine but not being detected, then the main electronic control board (which includes the water level pressure switch) will usually need to be replaced. Parts named: inlet water valve assembly, main electronic control board.

• The water supply faucets behind the washer are not fully open: F8 E1 appears and no water enters the tub. Check the water supply faucets behind the washer are fully open
• Kinked fill hoses or clogged inlet valves: Water reaches the hoses but only slowly enters the washer. Check the fill hoses and the inlet water valves
• A defective inlet water valve assembly: The hoses and faucets are good and no water enters. The chart replaces the inlet water valve assembly if it is defective
• Water enters but is not detected, so the board misreads the level: The tub fills but the code still appears on the display. The chart says the main electronic control board, which includes the water level pressure switch, will usually need to be replaced

If the washer isn't filling, start behind the washer with the faucets, since a half-open faucet is the cheapest cause.

Look for kinks and clogged screens, and replace the inlet water valve assembly if it is defective.

The chart says the board includes the water level pressure switch and will usually need to be replaced.

Inlet water valve assembly and main electronic control board.

Towels, a bucket and a screwdriver or nut driver.

What about the Wash LED? The Wash LED on entry has the same chart text, for models that show lights rather than codes.

Shut the faucets if a hose leaks or the tub overfills

The board is the last and costliest part, so check the supply and the valve first

Kenmore 110 model VMAX top-load washer code F8 E3

Listed as overflow condition.

If the washer is overfilling, check the inlet water valves. If the valves are not shutting off water flow, then replace the inlet water valve assembly. If the washer isn't actually overflowing, then the main electronic control board (which includes the water level pressure switch) will typically need to be replaced. Parts named: inlet water valve assembly, main electronic control board.

• The inlet water valves are not shutting off water flow: F8 E3 appears and the tub keeps on filling past its level. Check the inlet water valves; the chart replaces the assembly if they do not shut off
• A water level reading that is wrong while the washer is not actually overflowing: The tub is not overfull but the code appears. The chart says the main electronic control board will typically need to be replaced in that case
• A leaking valve that fills the tub with the washer off: The tub gains water even when the washer is unplugged. Unplug the washer and see whether water continues to enter

If the washer is overfilling, see whether the inlet valves are shutting off the water flow when the cycle stops.

The chart names the inlet water valve assembly as the part when the tub really overfills.

The chart says the board, which includes the water level pressure switch, will typically need to be replaced.

Towels and a screwdriver or nut driver.

What if the washer isn't overflowing? The chart replaces the main electronic control board, which includes the water level pressure switch.

How do I check the valves? See whether they shut off the water flow.

Shut off both water faucets at once if the tub keeps filling

Unplug the washer before you check the inlet valves

Kenmore 110 model VMAX top-load washer code F8 E5

Listed as hot & cold fill hoses are reversed.

Check the fill hoses.

If they are connected properly then the inlet water thermistor (temperature sensor) will probably need to be replaced. That component is part of the Inlet Water Valve Wire Harness. Parts named: inlet water valve wire harness.

• The hot and cold fill hoses are connected the wrong way round: F8 E5 appears and hot water arrives where cold is expected. Check the fill hoses at the faucets and at the washer
• A faulty inlet water thermistor that misreads the water temperature: The hoses are connected properly and the code remains. The chart says the thermistor will probably need to be replaced
• A damaged inlet water valve wire harness: The thermistor in the harness reads the temperature wrongly. Replace the inlet water valve wire harness, which includes the thermistor

Look at the positions of the hoses at the faucets and at the back of the washer. The chart's first check is whether they are reversed.

The chart says the thermistor (temperature sensor) will probably need to be replaced, if the hoses are already right.

The chart says the thermistor is part of the inlet water valve wire harness, so the harness is the part.

Inlet water valve wire harness (includes the thermistor).

What if the hoses are right? The inlet water thermistor will probably need to be replaced, per the chart.

How do I tell the hoses apart? Hot is usually marked red and cold blue at the hose ends or the faucets.

Do not touch very hot water from the hose; let it run and check with care

Unplug the washer before working on the inlet valve wire harness

Kenmore 110 model VMAX top-load washer code F9 E1

Listed as long drain time.

The washer isn't draining after the drain pump runs for 10 minutes. Check the washer drain and the drain hose for clogs or restrictions. If the drain path is clear, unplug the washer and check the drain pump. If the drain pump is defective, replace it. Parts named: drain pump.

• A clog or restriction in the washer drain or the drain hose: F9 E1 appears and the tub still holds water after the pump has run for 10 minutes. Check the washer drain and the drain hose for clogs or restrictions
• A clogged or defective drain pump: The drain path is clear but water stays in the tub. Unplug the washer and check the drain pump
• A kinked drain hose behind the washer: The hose is crushed after the washer was pushed back. Look for kinks or crushing along the whole drain hose

The chart says the washer isn't draining after the drain pump runs for 10 minutes, so start with the drain path.

Look for lint, a coin or a sock in the pump, with the washer unplugged and the tub bailed out.

The chart names the drain pump as the only part for F9 E1 on the VMW.

Drain pump.

A shallow pan, towels and a screwdriver or nut driver.

What about the Spin LED? The Spin LED on entry has the same chart text, for models that show lights rather than codes.

Unplug the washer and bail out the tub before working at the pump

Do not keep running cycles with a tub that will not empty

Kenmore 110 model VMAX top-load washer code Lid Lock LED flashing

Listed as indicates the control recorded one of the error codes shown below.

Enter the diagnostic test mode to read the error code as shown in the above video link.

• The control has recorded one of the washer's error codes and shows it by flashing the Lid Lock LED: The Lid Lock LED flashes and no code appears in the display. Enter the diagnostic test mode to read the recorded error code
• A lid lock or lid switch fault that the LED is flagging directly: The LED flashes when you close the lid or press Start. Read the code first, then use the F5 E1 to F5 E4 pages for the lid parts
• An unrelated recorded fault such as a fill, drain or motor code: The washer stops mid-cycle and the Lid Lock LED flashes. Read the recorded code in diagnostic mode before you change any part

The chart says it indicates the control recorded one of the error codes listed for this washer, so the real fault is one of those.

The chart points to a how-to video on troubleshooting flashing lid lock errors on a vertical modular washer; the steps for your model are on that video and in the service sheet.

Use the page for that code, such as F0 E2, F5 E2 or F9 E1, and follow its checks and parts.

Lid Lock LED flashing (110 model VMW table).

None; it points to the recorded code.

The diagnostic test mode; a screwdriver or nut driver for any later repair.

What does the Lid Lock LED flashing mean on a Kenmore VMW washer? The control recorded one of the error codes, in the chart's words.

How do I read the code? Enter the diagnostic test mode, as the chart's video shows.

Is the lid lock broken? Not necessarily. The LED points to any recorded code, so read the code first.

Do not replace the lid lock/switch assembly just because the Lid Lock LED flashes, since it is showing a recorded code from any part

Unplug the washer before opening the console or lifting the top panel

Kenmore 110 model VMAX top-load washer code Spin LED on

Listed as long drain time.

The washer did not drain after the drain pump has been running for 10 minutes. Check the washer drain and the drain hose for clogs or restrictions. If the drain path is clear, unplug the washer and check the drain pump. If the drain pump is defective, replace it. Parts named: drain pump.

• A clog or restriction in the washer drain or the drain hose: The Spin LED stays on and the tub still holds water. Check the washer drain and the drain hose for clogs or restrictions
• A clogged or defective drain pump: The drain path is clear but water stays in the tub. Unplug the washer and check the drain pump
• A kinked drain hose behind the washer: The hose is crushed after the washer was pushed back. Look for kinks or crushing along the whole drain hose

The chart says the washer did not drain after the drain pump has been running for 10 minutes, for models that show lights.

Then, if the drain path is clear, unplug the washer and check the drain pump.

The chart names the drain pump as the only part for the Spin LED on.

Spin LED on (110 model VMW table).

Drain pump.

A shallow pan, towels and a screwdriver or nut driver.

What does the Spin LED on mean on a Kenmore VMW washer? A long drain time, in the chart's words.

How long does the pump run first? 10 minutes, per the chart.

Unplug the washer and bail out the tub before working at the pump

Do not keep running cycles with a tub that will not empty

Kenmore 110 model VMAX top-load washer code Wash LED on

Listed as no fill or long fill.

Water isn't being detected as entering the washer. If the washer isn't filling, check the water supply faucets behind the washer to make sure that they are fully open. Check the fill hoses and inlet water valves. If the inlet water valve assembly is defective, replace it. If water is entering the machine but not being detected, then the main electronic control board (which includes the water level pressure switch) will usually need to be replaced. Parts named: inlet water valve assembly, main electronic control board.

• The water supply faucets are not fully open: The Wash LED stays on and no water enters the tub. Check the water supply faucets behind the washer are fully open
• Kinked fill hoses or blocked inlet valves: Water is slow to enter the tub after Start. Check the fill hoses and the inlet water valves
• A defective inlet water valve assembly: The hoses and faucets are fine and no water enters. The chart replaces the inlet water valve assembly if it is defective
• A water level reading fault on the control board: Water enters and the Wash LED still stays on. The chart says the main electronic control board will usually need to be replaced

The chart lists this indicator light with the same instruction as the F8 E1 code, for models that show lights.

If the inlet water valve assembly is defective, replace it, and check the hoses and the faucets first.

The chart says the board, which includes the water level pressure switch, will usually need to be replaced.

Wash LED on (110 model VMW table).

Towels and a screwdriver or nut driver.

What does the Wash LED on mean on a Kenmore VMW washer? No fill or long fill, in the chart's words.

Shut the faucets if a hose leaks or the tub overfills

The board is the last and costliest part, so check the supply and the valve first